Matronics Email Lists

It's grounded on the ground bus were all my items are coming. Same ground like voltmeter 2.

I will try thank you Wink

When you tell "loop wire around the switch" it's around the conne ...

Hi all,

I send a message because I have since months a noisy voltmeter after the total change of my electrical system. And I tried to resolved it without good evolution.

I have used the book ...

Hi all,

I have a question about a problem that i have with my new electrical system.

I have a two way switch with 2 voltmeters, one for the main battery and the other one for the aux, still hot ...

At the end it cost me just a few cents, one diode and 3cm of wire. I just didn't test my ignition but all the others things are working.

Thanks you bob !!! Wink

I will advise you this weekend I will asses.

The contactor wire is the only one that is alone, so it will be easy to change it if it's the only one that could be damage. In my mind it don't keep c ...

Thank you bob for you reply. I hope to find just the diode end the wire U/S. Many thanks.

I have to check just the intégrity of contactor ground wire (master switch to the ground bus) easily acces ...

Good day,

After some months wiring my plane with Z19, long months, today was the day to set the master switch in ON... Wink

And I did a mistake... THE mistake. (The Ridiculouse mistake !!!) ...

Thank for your reply andy, i did not see it.

I was thinking about more easy and simply gadget. Just with buzzer and led.

I have done a drawing for my 3 systems alarm to begin, now I have to set ...

Many thanks Joe and Bob for you reply.

I am reading again the book and it refresh my "knowledge" very well.

So I will let my alternator WHITOUT ground wire if I understand well;

My ...

Good morning,

I send a message about ground loops and ground, I let my electrical system without finishing my work on it since months due to winter and other things.

Yesterday I decided to fini ...

Good day !

I need some help to wire an alarm (souder and one red light) with multiple sources.

I have my ignition sending a signal on an exit to power up an alarm souder up to 75ma, I want to us ...

Now when I ask, it's for an engine Boat Laughing

But it's true that Buggy smell better, I keep it in my mind. Wink

As it was linked on an aircraft part website I explained the t ...

Thank you Werner,

I will contact them. I didn't know this website.

I have contacted before fastelane.ltd as told in the aviation seller website but... they don't want to sell their products for ...

Hello,

Finishing to wire the Z19RB on my plane, I have a problem to resolve... the latest before flying again ! Rolling Eyes

Something is missing between sparks and ignition coil... And to chose ...

Hello,

I have a question about crimping 2 AWG wire. I was wiring my plane and it came the time to wire my 2 AWG cable.

For that I bought a crimping tool, this : (Not the best I agree)

http ...

Hello all,

I have another question about my wiring diagram just before to begin on the plane. (4 questions) :

1) I followed the Z19R diagram, but my auxiliary battery is a small 7ah. (Main 18ah ...

Yes in respons to pilot input.

Little input didn't run the motor, a bit large input pass through the value desired. (no possible to adjust it precisely) but maybe it's not the fault of the relay. ...

Hello again,

Just to ask a question about this OVP wiring.

I have a filter with it (b&c complet OVP system) for the relay I didn't put it to wire it like the diagram, but the filter have to ...

Thank you bob,

I haven't see the response before and I answered in other topic.

I will try it and I will come back to tell if it run better or not. (if it run well also to tell what it was bad ...

Hello,

Thank you I will do it, it's true that before wire was twist only 3 inch. and the other wire for the trim/switch trim/bus were not.

For the wiring I find a wiring diagram for a car relay, ...