Matronics Email Lists

I've got the Terminal Tool and it does a great job if you can put it in a
vice. Used as a portable tool it is pretty awkward. I made it work and the
results were fine but, as I say, it was a littl ...

It will be interesting to see how long the Subaru will run on one battery if
the alternator goes out.

--

Roger,
I am using Z-19RB in my Subaru H6 powered RV7. My understanding as to why
the endurance bus alternate feed is from the Main Battery only is that the
engine bus and its battery are reserved ...

For what it’s worth the original attachment worked for me.
Allen Fulmer
RV7

_____________________________________________
From: owner-aeroelectric-list-server@matronics.com On Be ...

Subaru engine with dual electrical system including pair of Odyssey PC625’s.

Left one battery master switch on all night!
6 yr. old PC625 on that master reading only 6.4 volts.
Optimizer b ...

I have the exact same thing and will wire it up the way you have described. Except remember that the “N” stands for Neutral and is usually grounded at the breaker box and usually the whit ...

Thanks you Bob.

Do not archive

From: owner-aeroelectric-list-server@matronics.com On Behalf Of Robert L. Nuckolls, III
Sent: Friday, February 18, 2011 10:06 AM
To: aeroelectric-list@matronic ...

Bob,

I there a drawing showing the circuit you describe below? And values/part no. for the power diode and relay?

Thanks,

Allen Fulmer

Do not archive

From: owner-aeroelectric-list ...

I figured some folks might install without a tray? Mine are still in the
box awaiting a shop cleanout event.

Allen Fulmer
RV7 Panel with 430W finished, working on cowl
N808AF reserved

I “split the difference” with SteinAir for $17.50: “3 Piece 90 Degree Right Angle Male BNC Crimp Connector for RG-400 & RG-58 Coax Cable. Uses the same crimper as standard BNC's. ...

Mike – Do you have an EFIS? I know my GRT Horizon will display the trim servo position using the 3 wires you mention. I suspect the other EFIS players will do likewise.

By the way, I h ...

AC 43.13-1B, chapter 11, page 11-76, has several sketches of lugs connected
to various bolts, studs, etc. Depictions of installation order of washers,
lock washers, lugs, etc. I didn't look for simi ...

It has been several years since I inventoried my finish kit so I have kind of lost track of which hinge goes where and why.

If I understand DWG#45 for RV7 there are two types of hinges materia ...

That looks just like the one I bought from West Marine. Probably cheaper too.

Once fat wire was connected to above “pass through terminal” at the firewall I branched off to a four ...

I have one you would be welcome to borrow. 3-1/8 on one side, 2-1/4 on the
other. Kind of heavy but maybe one of those "if it fits it ships" USPS
boxes wouldn't be too much.

Allen Ful ...

I like that Bob. I am going to quit feeling guilty for adding all those
gadgets that I think I will enjoy. Those seat heaters, O2, etc., will feel
just right at 16,000 feet as I fly over the Rocki ...

I ran two conduits before floor was fastened down. Wish I had run 4. Of
course I am all electric with batteries in tail because of Subaru on the
firewall. I put transponder antenna and couple of w ...

I used stud pass through I purchased from West Marine online.

Allen Fulmer
RV7 Finish wiring

Not sure if this is actually relevant to the original question but I bought the Cole Hersee Piper style socket and plug from Aircraft Spruce after reading Bob N’s article on modifying for our OB ...

-- Tim said:-- There will be an Avionics master or at least an EFIS master as these units have no-- on/off switch, and GRT asks for one. I believe they would be protected anyway with-- Z-10/8 but I ...