Matronics Email Lists

>Also, the modification to strengthen the counterweight installation was deemed necessary due to a bent arm, I gather.Has it been considered if cushioning of the mass before end of travel could ach ...

I’m very pleased with my Airmaster.

Very Robust
Very well made.
Good Performance improvements over my fixed pitch warp drive.
Maintains RPM set
2000 hours between overhauls and with 100hour ...

I burp exactly as described after the last flight of day.

There is no siphon back even over several days between flight.

I think there is an air gap in the return to the tank, otherwise you woul ...

I have four “u” bolts at each corner of the baggage bay. They are bolted to hard points made by floxing a ply layer under the bay floor..

You can get a cargo net from any motorcycle dealer as t ...

Don’t forget that you have the slots for the flaps which are below the wing during normal flight and may influence the pressure in the rear that you will need to compensate for.

Alan

Sent from ...

Because you may find that the air pressure behind the D panel is higher than the cockpit and so you will simple see air coming from the rear to the cockpit unless you have some arrangement in the tail ...

G-IANI is indeed still flying, I know the owner is on the WhatsApp group but not sure about this one.

I had that mod installed on mine, G-OBJT but could not see any benefit and blocking it off decr ...

I have made pitot and fuel vent covers from clear plastic tube. The tube is bent double and slips over the fuel vents and also Pitot:static and has the red remove before flight tags attached.

Alan ...

I wonder if it’s worth adding an item to 6mon/50Hr/ Annual to reverse blow the vents to clear any crud collected?

Alan.

Sent from my iPhone

On 30 May 2023, at 16:23, olivier.hequet@neuf.f ...

I have 5-6cm square hinged flaps cut into the sides of the fairings, secured with a single screw into a captive nut.

There is just enough room to get you fingers through the hole after you rotate t ...

I am a Europa Club Member and have just downloaded the STL files at no cost from the club website so I don’t understand your comment;

>In reality a club member still has to purchase the STL 3D ...

Someone on the WatsApp group were offering to do just that. I suggest a message on that group might get a response or even a link to a printing company that will do them.

You could always whittle d ...

On 16 May 2023, at 02:25, JonathanMilbank <jdmilbank@yahoo.co.uk> wrote:

--> Europa-List message posted by: "JonathanMilbank" <jdmilbank@yahoo.co.uk>

Please would som ...

Not had a problem.

Whenever I’ve come across something that’s doesn’t seem to work I always go back to the manual to check I have the right items and assembled them correctly.

For exampl ...

Is this an alternative to the Tygon Tube we are all talking about?

Alan

Sent from my iPad

On 19 Feb 2023, at 19:18, Matt Dovey <mattdovey@hotmail.co.uk> wrote:

Jonat ...

This is what I have on file that may help. I’ve also copied them to Bob Hitchcock for possible inclusion on the Europa Club website.

Alan Burrill

On 18 Jan 2023, at 12:01, daaza22 < ...

David

The GPS 196 is only able to output at 0.5Hz i.e. every 2 seconds. I originally used an AVMap EKP-V and that also did 4800 baud and 2 second update. The AP function ok but I did notice some in ...

Service bulletins sb-912-043-r2 and sb-914-029-r3 issued November 2006 uplifted the radiator pressure cap to 1.2bar.

It also has the ROTAX part no for the replacement.

I owned a Triumph Sprint m ...

I have an EarthX and the Rotax Ducati Regulator. It charges the EarthX and not had any problems.

Alan

Sent from my iPhone

On 19 Dec 2022, at 11:23, Pete Zut <peterz@zutrasoft.com> wrot ...

Spade connectors of that size are rated to 10 amp and 300v according to the R/S-Components specification sheet.

Alan

Sent from my iPad

On 18 Dec 2022, at 21:53, Bob Harrison <ptag.dev@talk ...