Matronics Email Lists

Check the RPA store or Desser

On Thu, Aug 15, 2024, 15:29 David Jester <wdjester@cox.net ([email]wdjester@cox.net[/email])> wrote:

[quote]--> Yak-List message posted by: David Jester &l ...

Harv,

I'm not aware of any fuse prior to the Master switch. It is a pain but have you checked the voltage at the master switch. The master switch may have failed internally and although you hav ...

Justin,

Not only did I clean the cannon plug, I took mine apart and reset the wires. For me in the beginning,it was a dirty/loose cannon plug. Issue came back and when I reset the wires, I cleare ...

I can't relate to the filler port but in other situations, I put the rubber grommet in very hot water to get it more flexible, a little silicone grease on it and work it in. I have used this on ...

I purchased the entire nose gear assembly. Basically plug and play. Slide the large pin out of the upper fork, disconnected the drag link, put the new unit on, re-attached the drag link, installed t ...

I purchase the entire nosegear strut assembly complete. All I had to do is remove the large pin holding the nose strut near the lower firewall, lower the unit, reinstall the new assembly and put the t ...

I fought this same issue for year. Thought is was a dragging brake, replaced the upper bushings. Measured alignment of main gear. Adjusted the dampner arm.
Finally gave up, bought a new complete asse ...

Steve,

Ah the world of air leaks. We all go thru this on a constant basis and through the years we have all tried different methods. We have converted metal lines to high tech flex lines, changed a ...

John,

First of all congrats on your purhase. You are in a great area. Besides the folks in Louisville, you have some folks in Columbus IN, Indianapolis, and Cincinnati areas. Best to go to the Re ...

Leave California!!

On Tue, Dec 7, 2021, 16:36 yakflyr <yak55m@gmail.com (--> Yak-List message posted by: "yakflyr" <yak55m@gmail.com (

Try cleaning the valve housed in the banjo fitting on the compressor.

On Sun, Nov 28, 2021, 19:15 1906 <zmadwolf@gmail.com (--> Yak-List message posted by: "1906" <zmadwolf@gma ...

Several years ago GT Propellers out of Italy were touting the development of a new propeller blade that was a direct replacement for the existing Chinese metal blades.

Does anyone know if t ...

My two feeble sense worth.

Walt mentions a mixture issue with a possible weld issue on the drain kit of 4,5 and 6. I would check each intake tube to insure they are snug. Any chance your primer i ...

By chance, does anybody have a serviceable CJ step laying around? If so, please give me a shout out.

Greg Clouddog Wrobel

Test good

Greg "Clouddog" Wrobel

On Sat, May 29, 2021, 10:18 Matt Lazar <mattlazar@hotmail.com (
test

From: Yak-List Digest Server (Sent: Saturday, May 29, 2021 2 ...

Sticking valves happen. We have all had them. The danger is when you let them go you may eventually burn the valve and then you have another issue to deal with. When you pull through in a perfect worl ...

Ok, I may need some help here. It's early, I haven't had my coffee yet and I am but the sharpest knife in the drawer. I saw where you started at the #1 cylinder and went counter clockwise. The ...

Excellent advice on addition of a fuel computer. I have installed one on both airplanes I have owned and I believe the unit is perhaps one of the most important pieces of equipment add on's you ca ...

Did I leave out that I do all this outside in a 20 acre rock quarry using a robot handling the sprayer and have my aircraft insured for 10 times what's its worth?? What could possibly go wrong. ...

I use 100LL through a wand that has a pickup tube and use 80-90 psi from my compressor that is part if the pickup tube system. Available at Harbor Freigh. It melts the grease and evaporates before it ...