Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Search found 18 matches
Matronics Email Lists Forum Index
Author Message
  Topic: FireFly Trailer With Clamping Wheel Chocks
Dnul

Replies: 0
Views: 2153

PostForum: Kolb-List   Posted: Sun Oct 05, 2014 4:25 pm   Subject: FireFly Trailer With Clamping Wheel Chocks
The picture shows a weldment I use to chock my wheels on a home-made 20-foot trailer, with 36-inch tongue. The wheels roll up over a hinged part that swings up to immobilize the wheel when tied up ...
  Topic: Kawasaki 440A FireStar
Dnul

Replies: 0
Views: 1929

PostForum: Kolb-List   Posted: Sat Nov 09, 2013 6:19 pm   Subject: Kawasaki 440A FireStar
Picture of FireStar with Kawasaki 440 exhaust.
  Topic: Drilling Center Of Tube
Dnul

Replies: 3
Views: 5036

PostForum: Kolb-List   Posted: Fri Jul 12, 2013 10:26 am   Subject: Re: Drilling Center Of Tube
http://www.skygeek.com/eastern-edf1-drill-rite.html sells the drill guide.
  Topic: Drilling Center Of Tube
Dnul

Replies: 3
Views: 5036

PostForum: Kolb-List   Posted: Fri Jul 12, 2013 10:22 am   Subject: Re: Drilling Center Of Tube
That would be great to order for drilling the vertical stabilizer post, the drag strut, or the landing gear leg and the universal joint on the aileron control tube which would be drilled inaccurately. ...
  Topic: Jig To Install Hinges
Dnul

Replies: 3
Views: 4223

PostForum: Kolb-List   Posted: Fri Jul 12, 2013 10:07 am   Subject: Re: Jig To Install Hinges
My other tip shows cutting bushings and someone asked "what bushings" on this thread showing the hinge drilling jig. FireFly uses bushings cut from 5/16 ID steel tube. They are used where ...
  Topic: Latex Pain Forum
Dnul

Replies: 16
Views: 14239

PostForum: Kolb-List   Posted: Fri Jul 12, 2013 9:52 am   Subject: Re: Latex Pain Forum
How would you use cheap house paint to do a small graphic detail on top of Polytone, on fabric, in order avoid buying some quarts of Polytone? You can get small sample cans of latex mixed colors at L ...
  Topic: Drilling Center Of Tube
Dnul

Replies: 3
Views: 5036

PostForum: Kolb-List   Posted: Thu Jul 11, 2013 10:36 am   Subject: Drilling Center Of Tube
To drill the center of a tube use a "V" block. Simply lower the drill on the drill press down to the bottom of the "V" to position for center.
  Topic: Fitting an un-drilled panel onto blind tabs
Dnul

Replies: 4
Views: 4019

PostForum: Kolb-List   Posted: Thu Jul 11, 2013 10:33 am   Subject: Re: Fitting an un-drilled panel onto blind tabs
Wicks has sheet back markers and strap duplicators.
  Topic: Fitting an un-drilled panel onto blind tabs
Dnul

Replies: 4
Views: 4019

PostForum: Kolb-List   Posted: Thu Jul 11, 2013 10:10 am   Subject: Re: Fitting an un-drilled panel onto blind tabs
Wicks has sheet back markers and strap duplicators.
  Topic: Rudder Spring Length FireFly Question
Dnul

Replies: 4
Views: 4140

PostForum: Kolb-List   Posted: Thu Jul 11, 2013 10:03 am   Subject: Re: Rudder Spring Length FireFly Question
I should get a 3/8" dia aluminum tube 8 and 3/4 inch long to hook the springs to so they're stretched 1 and 3/4 inches to get to the pedals in neutral since that is what the plans call for.
  Topic: Rudder Spring Length FireFly Question
Dnul

Replies: 4
Views: 4140

PostForum: Kolb-List   Posted: Wed Jul 10, 2013 10:23 am   Subject: Rudder Spring Length FireFly Question
The picture of a new factory-built FireFly shows that the longitudinal axis of a rudder spring must bend whenever a rudder pedal is pushed. Would it be better if the spring on a pedal that is pressed ...
  Topic: Marking Center Of Tube
Dnul

Replies: 3
Views: 4101

PostForum: Kolb-List   Posted: Wed Jul 10, 2013 9:55 am   Subject: Marking Center Of Tube
Picture shows how to mark the center line of a tube using a C-Thru brand ruler.
  Topic: Sport aviation mag.....
Dnul

Replies: 4
Views: 4093

PostForum: Kolb-List   Posted: Sat Jun 15, 2013 8:18 pm   Subject: Re: Sport aviation mag.....
http://www.contactmagazine.com/FreeLunch.html
  Topic: Sport aviation mag.....
Dnul

Replies: 4
Views: 4093

PostForum: Kolb-List   Posted: Sat Jun 15, 2013 7:34 pm   Subject: Re: Sport aviation mag.....
http://www.contactmagazine.com/FreeLunch.html
  Topic: Sport aviation mag.....
Dnul

Replies: 4
Views: 4093

PostForum: Kolb-List   Posted: Sat Jun 15, 2013 7:30 pm   Subject: Re: Sport aviation mag.....
http://www.contactmagazine.com/FreeLunch.html
  Topic: Sport Instructor Central Ohio
Dnul

Replies: 0
Views: 1685

PostForum: Kolb-List   Posted: Sat Jun 15, 2013 8:50 am   Subject: Sport Instructor Central Ohio
http://www.heavenboundaviation.com/
Aircraft Dealer, Engine Dealer/Rebuilder, Airfield, Electronics.
Cell: 740-644-4690
Address: 8878 Harmony Church Rd., Johnstown, OH 43031
  Topic: Jip To Cut Bushings
Dnul

Replies: 0
Views: 1699

PostForum: Kolb-List   Posted: Sat Jun 15, 2013 8:43 am   Subject: Jip To Cut Bushings
Bushing can be cut square to an exact length. Use bee's wax on hacksaw.
  Topic: Jig To Install Hinges
Dnul

Replies: 3
Views: 4223

PostForum: Kolb-List   Posted: Sat Jun 15, 2013 8:36 am   Subject: Jig To Install Hinges
The picture shows a jig which immobilizes the hinge in position for drilling.
 
Page 1 of 1
All times are GMT - 8 Hours
Jump to:  


Powered by phpBB © 2001, 2005 phpBB Group