Matronics Email Lists

Here are some ISS and VDO gauges

This is the drawing of my ISS Sender install in my tank. My tanks have been modified and follows the wing profile... curved top!

Here i ...

Hey Jimmy

Get rid of that VDO junk! I made the mistake of buying them and they are just plain junk... ok
for a VW car, but not for an aircraft! My VDO junk is for sale now cheap!

I have repl ...

Try DeltaCad... it is simple and very easy to use! I have been using it for years! [url=http://www.deltacad.com/]http://www.deltacad.com/ I have a number of CAD programs... including ...

G'Day Perry...

That change in the photo assembly was in Sept, 2009... still lots of time for them to update
the drawings, I guess the 750 was more important!
Ron

:--)>
:--)>
:--)> ...

Hey Perry...

Look at the enclosed PDF for the answer! This from the Zenair newsletter from 1999... where
CH offered a solution to the elevator trim problems as well as with the flaperons. The ...

Hey Bob...

I'm looking at Z-12! Can you tell me the difference between the Battery Contactor(no number)
on Z-12 and B&C's - S701-1? Are they the same... and Can the S701-1 be used for th ...

Thanks Joe...

That is for a 1 wire, I have a 3 wire... is there much difference?

Ron

:--)>
:--)>
:--)> Here is another link to modifying an alternator:
:--)> http://www.eaa.org ...

Thanks Roger...
Ron

:--)>:--)> I have a 3 wire internally regulated alternator... that I would like to
:--)>:--)> convert to external regulator!
:--)>:--)>
:--)> Here is on ...

Thanks John... my alternator is a 40A Denzo 3 wire. It's pretty hard to make out from the
photos!

Ron

:--)>
:--)>
:--)> Ron,
:--)> Try this
:--)>
:--)> http://home ...

Thanks bob...

I have a 3 wire internally regulated alternator... that I would like to convert to external
regulator!

Is there any info online somewhere that provides instructions to do the c ...

I need some help here with alternators! What is the difference between a 1 wire and a 3 wire
system?

Can a 1 wire setup be shut down with a switch as per over voltage protection... or does i ...

No... one is the primary pump and the other is the secondary(backup) pump on my battery bus!

:--)>
:--)>
:--)> Now you have twice the pressure, & lose half that if one pump fails. If ...

Not in parallel... series only!

:--)>
:--)>
:--)> If I understand the 'no check valve' spec correctly, if 2 are plumbed in parallel
:--)> you'll be either pumping into the opposite t ...

Hey Dj...

I'm also going with the Rotex TBI-34! With the remote pressure regulator (they
recommend a 0.5 - 6.0psi) I will be using two(20) - Facet #40108 inline(no check
valves - 4.5- 6.0psi) ...

Dave... where is the photo and the rest of your post????

Ron

:--)>
:--)> <chilledj@yahoo.com>
:--)>
:--)> i don't have the stops in for the aileron bell crank yet so i
:--) ...

Haven't checked back here for a while. Thanks for the article.I still find it a bit disheartening that no one at can -zac could return my calls or answer my e-mail that i sent a month ago. Funny way t ...

Hey Espuny...

Have tried to access the web site ling you sent... but it is not working! Is there a problem?
Ron Leclerc
Canada
:--) --> Kitfox-List message posted by: "Franci ...

Hey James...

This tool can be purchased on Ebay cheap... I have one and works great!
This tool is nice to have on hand... here is the ebay link, probably made
in China!

http://shop.ebay.com ...

Jimmy...

You would have to ask Matco where they get there tires from! I looked
long and hard to find out who has these tires and tubes other then Zenair!
I used the tire and tube spec from ...

Hey Phil

This is the tire and tube you should have... not Carlisle!!!!

http://www.matcomfg.com/TIRE800X64PR-idv-2991-38.html

http://www.matcomfg.com/TUBE800X67-idv-3081-38.html

Ron

:--) ...