Matronics Email Lists

Hi Joe,

I remember seeing a guide about Guenhagen; what to bring, what not to bring when staying there, etc. I can't find it again! Do you remember it?

Dino

On Wed, Jul 13, 2011 ...

From the Home Depot Canada web site:

[url=http://www.homedepot.ca/webapp/wcs/stores/servlet/CatalogSearchResultView?D=948980&Ntt=948980&catalogId=10051&langId=-15&storeId=10051& ...

Hi Ernie,

I know that on my Canadian license I can fly a Canadian registered aircraft in US airspace, but I can not fly a US registered aircraft. I believe these rules are reciprocal, so bottom lin ...

It is also possible to assemble your own in-the-ear headset. Have a look at [url=http://www.vansairforce.com/community/showthread.php?t 289]http://www.vansairforce.com/community/showthread.php?t 289 f ...

The text clearly says that the aircraft was a clone.

"...Le kit utilisÃ© par le constructeur est vendu par un fabricant polonais sans relation avec Zenair. La documentation de Zenair et celle ...

The angle of the ports doesn't matter, within reason. It's the angle of the surfaces to the relative airflow that causes a differential pressure.

On Jan 9, 2008 11:41 AM, pavel569 < pm56 ...

I bought mine at Home Depot.

Dino

On Nov 18, 2007 8:10 PM, Bob Unternaehrer <shilocom@mcmsys.com> wrote:

I know the number. just wondering what it was. Our country hardware store
...

Dan,

The case does connect directly to one of the pressure ports.

The black ring around the outer edge of the face is painted on. If you look at it from the side, you can see that clear plastic ...

Oops, I spoke too soon. I found the reference I was looking for at Dino Bortolin < dbortol@gmail.com ( lwinger <larrywinger@gmail.com ( --> Zenith-List message posted by: "lwinger" ...

I read somewhere recently that the HF gun is nicer than the Eastwood, but that the HF powders are not very good. I can't find where I read that.

Dino

On 8/15/07, lwinger <larrywinger@gma ...

Dave,

You could buy a length of clear tubing (3/8") at your local hardware store and use it to figure out your hose routing. Trim to length or mark it off and measure the length of the good ho ...

I'm no expert on this, but it sounds like a surface preparation problem to me. I just zinc chromated the inside of my rudder trim tab yesterday. I scuffed the surface with a Scotchbrite pad, washe ...

For anybody that needs a free image program, the Irfanview image viewer from Tim Juhl <juhl@avci.net ([email]juhl@avci.net[/email])> wrote:[quote] --> Zenith-List message posted by: "Tim ...

If you happen to be ordering something else from Scott Thatcher <s_thatcher@bellsouth.net ([email]s_thatcher@bellsouth.net[/email])> wrote:[quote] Dave,

Great idea... I can't be ...

My plane will fly in a year not yet determined. I'm planning to equip it for night VFR and OTT. My current plan is to use a Dynon D100 as the primary instrument, backed up by a lift reserve indica ...

I listen to Paul Riedlinger <paulried@rogers.com (

[quote][b] http://www.matronics.com/Navigator?Zenith-List http://forums.matronics.com [quote][b]

I was talking with a couple of the instructors at the school where I rent about their twin, which is a Piper Seneca. They said feathering the prop requires oil pressure from the engine, and if the RPM ...

I put the white dots in the artwork to help with alignment. Hold the assembly in front of a light and you'll be able to line things up easily. The dots are slightly undersized compared to the hole ...

Steve,

Keep it mind, a reamer makes a very accurately sized, _round_ hole.
The hole from a drill bit is only approximately round. They don't
accomplish exactly the same result. I'm not sure about ...

I'm surprised that it is able to get anywhere close to the requested
position with the feedback completely disconnected. Does it go to one
end of the travel first and then to the requested spot? If ...