Matronics Email Lists

Mono wheel classic, 912, warp prop, nice interior, factory trailer. 160hrs. tt

$15,000

PM me if interested
EG

I was syncing the carbs on my 912ul and tried to shut the engine down but turning off the ignition switches did absolutely nothing. I cycled them several time but the engine kept running. I finall ...

During some obviously ham handed treatment trying to get my ignition mounted I pulled one of the spark plug wires out of the ignition coil. Has anyone experienced this and is there a fix short of buy ...

Does anyone have the wiring diagram for an early Grand Rapides EIS ? This one has the two plug connection and is model EIS 3 adv-w/912. I have the operators manual but cant find the wiring diagram. ...

I'm looking for a 80 hp 912. Please PM me if you know of anything along those lines.

Thanks
EG

Kitfox III, currently flying with 912ul. Ivo three blade prop, Sept. annual 130 hr. airframe 350 engine, custom trailer made for Kitfox. Recovered 3 yrs ago. $16500. Will also sale with 582 and all ...

My 582 greyhead is showing 80 psi compression on both cyl according to my new compression guage. I think the recommended psi is 100. The engine runs well and is strong. Any suggestions on where el ...

Not sure how I ended up with the wide blades. I ordered everything per the folks in Lakeland when I was building the plane back in 1995-6. I was a early US builder so maybe the tapered blade part go ...

My monowheel classic has been in a bit of a time warp for the last 12 years or so and is very "old school". It has the 912ul and the orginal Warp Drive propellor from 1996. The prop blades ...

Hello All,

My doors bulge in the middle leaving about a 1/4 gap. Does anyone have any suggestions about how to cure this issue. I've heard mention of a mid door latch. Does anyone have a picture ...

My fuel selector hasn't been getting much exercise in the last few years and has gotten rather stiff to operate. It's awkward enough getting to it in the tunnel but as stiff as it is it's almost impo ...

I'm returning my early monowheel classic to flying status after a number of years being inactive. Getting caught up on the mods. I'm in the process of doing mod 73 the tailplane retention mod. Just a ...

Let me start by saying I'm the village idiot when it comes to radios so hopefully someone can point out the obvious problem to me. I'm trying to use my handheld (Vertex VXA 150) along with a set of P ...

I know this issue has been worked over a few times on the forum but I cant seem to find anything that matches my situation. Here's the deal, the 912 starts fine after warm up on the initial mag chec ...

Anyone have a part number or source for the O ring on the monowheel brake puck ?

thanks,

Skip Pate
monowheel A009

Mono wheel classic for sale. 912ul,warp drive prop, factory trailor, very nice interior intercom. 176 TT eng and airframe. $25000 OBO.
Will deliver to a port on the east coast for export.
Skip ...

I can't get the carbs on my 912ul to synch at both idle and about 4000rpm. If I adjust it for one setting it runs rough at the other. I'm using the dual throttle cable from ACS . Any suggestions ? ...

My mono wheel has been sitting up for an extended period in a warm climate and the top rear corners of the doors have warped up slightly from where the gas struts pushed on them. (orginal strut positi ...

After getting worrying indications on my 912 oil psi gauge I checked it out with a mechanical gauge. All was normal. So I obviously have a problem with my VDO guage or sender unit. Is there any wa ...

I located a metal container that looks like a cat food can (well actually it is a cat food can) It fits nicely around the bottom of the carb. I installed a 1/4 tube from the bottom to connect a drain ...