Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Another myth bites the dust.

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List
View previous topic :: View next topic  
Author Message
nuckollsr(at)cox.net
Guest





PostPosted: Thu May 31, 2007 12:54 pm    Post subject: Another myth bites the dust. Reply with quote

For a number of years, we've wrestled with a combination of
vague instructions and/or ol' mechanic's tales about using
high melting point solder on the pins of a pitot tube connector.

Thanks to the generous loan of his new 14v pitot tube, Bill
Crook made it possible to check this out.

After 2 hours of operation at 13.5 volts on the bench, a
thermocouple on the solder joints of the connector rose
to 240 degrees F, about 200 degrees lower than the melting
point for the solder.

Ordinary 63/37 solder is entirely suitable for making
these joints.

Thanks Bill. Your pitot tube is in the mail.
Bob . . .

----------------------------------------
( "Physics is like sex: sure, it may )
( give some practical results, but )
( that's not why we do it." )
( )
( Richard P. Feynman )
----------------------------------------


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
nuckollsr(at)cox.net
Guest





PostPosted: Thu May 31, 2007 1:20 pm    Post subject: Another myth bites the dust. Reply with quote

For a number of years, we've wrestled with a combination of
vague instructions and/or ol' mechanic's tales about using
high melting point solder on the pins of a pitot tube connector.

Thanks to the generous loan of his new 14v pitot tube, Bill
Crook made it possible to check this out.

After 2 hours of operation at 13.5 volts on the bench, a
thermocouple on the solder joints of the connector rose
to 240 degrees F, about 200 degrees lower than the melting
point for the solder.

Ordinary 63/37 solder is entirely suitable for making
these joints.

Thanks Bill. Your pitot tube is in the mail.
Bob . . .

----------------------------------------
( "Physics is like sex: sure, it may )
( give some practical results, but )
( that's not why we do it." )
( )
( Richard P. Feynman )
----------------------------------------


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
khorton01(at)rogers.com
Guest





PostPosted: Thu May 31, 2007 1:54 pm    Post subject: Another myth bites the dust. Reply with quote

On 31 May 2007, at 11:54, Robert L. Nuckolls, III wrote:

Quote:

<nuckollsr(at)cox.net>

For a number of years, we've wrestled with a combination of
vague instructions and/or ol' mechanic's tales about using
high melting point solder on the pins of a pitot tube connector.

Thanks to the generous loan of his new 14v pitot tube, Bill
Crook made it possible to check this out.

After 2 hours of operation at 13.5 volts on the bench, a
thermocouple on the solder joints of the connector rose
to 240 degrees F, about 200 degrees lower than the melting
point for the solder.

Ordinary 63/37 solder is entirely suitable for making
these joints.

What make and model was the pitot tube?

Kevin Horton RV-8 (finishing kit)
Ottawa, Canada
http://www.kilohotel.com/rv8


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
nuckollsr(at)cox.net
Guest





PostPosted: Thu May 31, 2007 6:08 pm    Post subject: Another myth bites the dust. Reply with quote

For a number of years, we've wrestled with a combination of
vague instructions and/or ol' mechanic's tales about using
high melting point solder on the pins of a pitot tube connector.

Thanks to the generous loan of his new 14v pitot tube, Bill
Crook made it possible to check this out.

After 2 hours of operation at 13.5 volts on the bench, a
thermocouple on the solder joints of the connector rose
to 240 degrees F, about 200 degrees lower than the melting
point for the solder.

Ordinary 63/37 solder is entirely suitable for making
these joints.

> What make and model was the pitot tube?

Aero Instruments. A PH-502-12 I believe.
Bob . . .

----------------------------------------
( "Physics is like sex: sure, it may )
( give some practical results, but )
( that's not why we do it." )
( )
( Richard P. Feynman )
----------------------------------------


- The Matronics AeroElectric-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> AeroElectric-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group