Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

tail wheel alignment

Matronics Email Lists Forum Index -> Kolb-List

View previous topic :: View next topic

Author Message

gaman(at)att.net
Guest

Posted: Sat Jul 28, 2007 7:25 pm Post subject: tail wheel alignment

I'm new to the list,so this may be old news to the veteran kolbists.After a few hrs the tail wheel spring begins to loosen in the tail post and allows the wheel to lean slightly.I think I've finally got a good fix.Removed the tail spring, sawed a horizontal cut 1/2 in deep in one side of the end of the tube,re-installed the spring and tail wheel assy,leveled the airplane,leveled the tail wheel then installed a two piece aluminum billet clamp bored to .875 before cutting it in-two, drilled and tapped with 2 counter bored allen head cap screws.Clamp is about 1/2 in thick and 1 1/2 in square.slipped it over the sawed portion of the steel tube and tightened it down .I then redrilled the retaining bolt hole 1 in aft of the original hole and secured it.Also lock tighted the full swivel tail wheel assy to the spring so it will not loosen at that point.Steers smoothly now,and is staying put.JB the carb socket guy machined it for  me

                              G Aman MK 3C Jabiru 2200

 [quote][b]

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

Thom Riddle

Joined: 10 Jan 2006
Posts: 1597
Location: Buffalo, NY, USA (9G0)

Posted: Sun Jul 29, 2007 3:39 am Post subject: tail wheel alignment

Gary,

Welcome to the Kolb List.



The description of your tail wheel mod is pretty good but a photo or 

two would be even better. Can you do that for us?



Thom in Buffalo

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

_________________
Thom Riddle
Buffalo, NY (9G0)

Don't worry about old age... it doesn't last very long.
- Anonymous

planecrazzzy
Guest

Posted: Sun Jul 29, 2007 3:55 am Post subject: Re: tail wheel alignment

Do you have compression springs ?



Alot of guys have change over to them .



There easy to make....Here's a couple of pictures...



.

.

.

Gotta Fly...

Mike & "Jaz" in MN

.

.

.

.

Ed

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

Tailwheel Compression Springs 002.jpg

Description:

Filesize:

57.45 KB

Viewed:

266 Time(s)

Tailwheel Compression Springs 001.jpg

Description:

Filesize:

57.26 KB

Viewed:

283 Time(s)

JetPilot

Joined: 10 Jan 2006
Posts: 1246

Posted: Sun Jul 29, 2007 7:00 am Post subject: Re: tail wheel alignment

I was reading the description, and about half way through gave up.  A picture is worth a thousand words....  A couple pictures would be great to really get an idea of your mod.



Mike

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

_________________
"NO FEAR" - If you have no fear you did not go as fast as you could have !!!

Kolb MK-III Xtra, 912-S

gaman(at)att.net
Guest

Posted: Sun Jul 29, 2007 10:55 am Post subject: tail wheel alignment

[quote][b]

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

gaman(at)att.net
Guest

Posted: Sun Jul 29, 2007 11:08 am Post subject: tail wheel alignment

Mike,

    I'm familiar with the mod you picture,but I have replaced the original springs with stiffer ones from Ace hardware.because of the taxi problem in stiff crosswinds.This mod just evens out the rudder pressures and takes the jerky response out of it

  thanks,G Aman

planecrazzzy <planecrazzzy(at)yahoo.com> wrote: 

Do you have compression springs ?



Alot of guys have change over to them .



There easy to make....Here's a couple of pictures...

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

Dave Bigelow

Joined: 29 Jan 2006
Posts: 103
Location: Kamuela, Hawaii

Posted: Mon Jul 30, 2007 12:13 am Post subject: Re: tail wheel alignment

Mike,



Where is your source for the compression springs?  Looks like a good way to go.

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

_________________
Dave Bigelow
Kamuela, Hawaii
FS2, HKS 700E

gaman(at)att.net
Guest

Posted: Mon Jul 30, 2007 11:21 am Post subject: tail wheel alignment

I hope my picture sending skills are better than my descriptions.

 Thanks G.Aman

JetPilot <orcabonita(at)hotmail.com> wrote: 



I was reading the description, and about half way through gave up.  A picture is worth a thousand words....  A couple pictures would be great to really get an idea of your mod.



Mike



--------

"NO FEAR" -  If you have no fear you did not go as fast as you could have !!!



Kolb MK-III Xtra, 912-S





Read this topic online here:



http://forums.matronics.com/viewtopic.php?p=126140#126140

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

CIMG1569.JPG

Description:

Filesize:

12.74 KB

Viewed:

272 Time(s)

CIMG1570.JPG

Description:

Filesize:

13.41 KB

Viewed:

270 Time(s)

CIMG1571.JPG

Description:

Filesize:

10.14 KB

Viewed:

255 Time(s)

Display posts from previous:

	Matronics Email Lists Forum Index -> Kolb-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum