Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Engine Choices

Matronics Email Lists Forum Index -> RV10-List

View previous topic :: View next topic

Author Message

apilot2(at)gmail.com
Guest

Posted: Thu Nov 29, 2007 9:23 pm Post subject: Engine Choices

Now, to break you away from the alternate engine wars.................

Has anyone considered a way to do taxi testing on your bird before flying, without worrying about break-in of new rings?

Seems to me that it would be a lot safer to only be test flying a new airframe, not a new airframe and a freshly built/overhauled engine. 

Definitely would not want to do any taxi testing on an engine that isn't at least somewhat broken in. Not to keen on the idea of taxiing out with brand fresh engine for first test flight, when you don't want to glaze cylinders, and you really don't know if engine is up to snuff, much less the airframe. 

Thoughts?

Comments?

  [quote][b]

Deems Davis

Joined: 09 Jan 2006
Posts: 925

Posted: Thu Nov 29, 2007 9:40 pm Post subject: Engine Choices

This has been on my mind a bit lately as well. If anybody has any ideas 

on this I'm all ears. Would there be enough cooling airflow with the 

aircraft tethered on the ground, uncowled?



Deems Davis # 406

'Its all done....Its just not put together'

http://deemsrv10.com/



Kelly McMullen wrote:

 	  Quote: 	
		   Now, to break you away from the alternate engine wars.................

 Has anyone considered a way to do taxi testing on your bird before 

 flying, without worrying about break-in of new rings?

 Seems to me that it would be a lot safer to only be test flying a new 

 airframe, not a new airframe and a freshly built/overhauled engine.

 Definitely would not want to do any taxi testing on an engine that 

 isn't at least somewhat broken in. Not to keen on the idea of taxiing 

 out with brand fresh engine for first test flight, when you don't want 

 to glaze cylinders, and you really don't know if engine is up to 

 snuff, much less the airframe.

 Thoughts?

 Comments?

 *

 *

speckter(at)comcast.net
Guest

Posted: Fri Nov 30, 2007 5:25 am Post subject: Engine Choices

Most engine shops have a hood that is mounted on the top of the engine that catches prop air and directs it down through the cylinders to cool them.   It is how they test run the engines they overhaul.  I rent the hood from the engine shop, install it on my engine while in the airplane and test run it at least 3 hours and more if I can.  I can thus check all instrumentation at the same time.  It is a boring job to sit there and be doing a full engine run for that long but it is the best way IMHO.  Don’t forget to tie the tail to a large tree, truck, or other immoveable object.  It will jump over chocks.  Ask me how I know.  

   

Gary  

40274  

         

  

From: owner-rv10-list-server(at)matronics.com [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Kelly McMullen

 Sent: Friday, November 30, 2007 12:23 AM

 To: rv10-list(at)matronics.com

 Subject: Engine Choices  

  

   

Now, to break you away from the alternate engine wars.................

 Has anyone considered a way to do taxi testing on your bird before flying, without worrying about break-in of new rings?

 Seems to me that it would be a lot safer to only be test flying a new airframe, not a new airframe and a freshly built/overhauled engine. 

 Definitely would not want to do any taxi testing on an engine that isn't at least somewhat broken in. Not to keen on the idea of taxiing out with brand fresh engine for first test flight, when you don't want to glaze cylinders, and you really don't know if engine is up to snuff, much less the airframe. 

 Thoughts?

 Comments?   	  Quote: 	
		    http://www.matronics.com/contribution 	
0 	  Quote: 	
		   	
1 	  Quote: 	
		   	
2 	  Quote: 	
		   	
3 	  Quote: 	
		   	
4 	  Quote: 	
		   	
5 	  Quote: 	
		   	
6 	  Quote: 	
		   	
7 	  Quote: 	
		   	
8 	  Quote: 	
		   	
9 	  Quote: 	
		  	
0 	  Quote: 	
		  	
1 	  Quote: 	
		  	
2 	  Quote: 	
		  	
3 	  Quote: 	
		  	
4

       [quote][b]

Deems Davis

Joined: 09 Jan 2006
Posts: 925

Posted: Fri Nov 30, 2007 5:48 am Post subject: Engine Choices

Gary any photos/links of what this 'hood' looks like? How difficult 

would it be to fabricate?



Deems



gary wrote:

 	  Quote: 	
		  

 Most engine shops have a hood that is mounted on the top of the engine 

 that catches prop air and directs it down through the cylinders to 

 cool them. It is how they test run the engines they overhaul. I rent 

 the hood from the engine shop, install it on my engine while in the 

 airplane and test run it at least 3 hours and more if I can. I can 

 thus check all instrumentation at the same time. It is a boring job to 

 sit there and be doing a full engine run for that long but it is the 

 best way IMHO. Don’t forget to tie the tail to a large tree, truck, or 

 other immoveable object. It will jump over chocks. Ask me how I know.



 Gary



 40274



 ------------------------------------------------------------------------



 *From:* owner-rv10-list-server(at)matronics.com 

 [mailto:owner-rv10-list-server(at)matronics.com] *On Behalf Of *Kelly 

 McMullen

 *Sent:* Friday, November 30, 2007 12:23 AM

 *To:* rv10-list(at)matronics.com

 *Subject:* Engine Choices



 Now, to break you away from the alternate engine wars.................

 Has anyone considered a way to do taxi testing on your bird before 

 flying, without worrying about break-in of new rings?

 Seems to me that it would be a lot safer to only be test flying a new 

 airframe, not a new airframe and a freshly built/overhauled engine.

 Definitely would not want to do any taxi testing on an engine that 

 isn't at least somewhat broken in. Not to keen on the idea of taxiing 

 out with brand fresh engine for first test flight, when you don't want 

 to glaze cylinders, and you really don't know if engine is up to 

 snuff, much less the airframe.

 Thoughts?

 Comments?



 *



 *

speckter(at)comcast.net
Guest

Posted: Fri Nov 30, 2007 6:52 am Post subject: Engine Choices

I do not have any pix.  It would not be difficult to make one.  It has

straight side walls that go from the rocker covers straight up.  It goes

from the rear baffle area arc forward to about 16" above the engine. It has

reinforcement angles to stiffen the larger panels.



Sorry I don't know more.   If I get a chance I will try and go over to the

engine shop and measure.



Gary

40274



--

RV10 4JF

Joined: 30 Nov 2007
Posts: 7

Posted: Fri Nov 30, 2007 7:11 am Post subject: Re: Engine Choices

Hi all, 



I've been lurking here for some time. I am hoping to order a tail kit at Sun n Fun 08.



When I overhauled my TSIO-520 I made a hood so I could do an on aircraft engine run-in, check engine parameters and setup the FI pressures. Setting up the pressures is an involved process and time consuming. 



I made a hood so the engine got proper air flow past the cylinder. In my case, I made it out of plywood and metal flashing from Home Depot. I then set it on my engine baffles and tied it to the engine. It worked pretty well. I followed an article I found on the subject of ground running an engine. 



I will take a picture tomorrow and see if I can post it.



JF

indigoonlatigo(at)msn.com
Guest

Posted: Fri Nov 30, 2007 7:39 am Post subject: Engine Choices

When you guys get one constructed and go to test it you should have a cam corder running just in case something unexpected happens, like the whole thing flies away, hits the windscreen, tumbles over the top of the plane, damages the tail cone and then takes out the vertical stabilizer and then lands on the horizontal stab.

  

 At least with the film you could send it in to America's funniest home videos and win the prize and pay for a new plane.

  

 JOhn G. 409 Just thinking out load

 

[quote] From: speckter(at)comcast.net

 To: rv10-list(at)matronics.com

 Subject: RE: Engine Choices

 Date: Fri, 30 Nov 2007 09:09:24 -0500

 

 --> RV10-List message posted by: "gary" <speckter(at)comcast.net>

 

 I do not have any pix. It would not be difficult to make one. It has

 straight side walls that go from the rocker covers straight up. It goes

 from the rear baffle area arc forward to about 16" above the engine. It has

 reinforcement angles to stiffen the larger panels.

 

 Sorry I don't know more. If I get a chance I will try and go over to the

 engine shop and measure.

 

 Gary

 40274

 

 --

carlosh(at)sec-engr.com
Guest

Posted: Fri Nov 30, 2007 10:44 am Post subject: Engine Choices

Here's a site with a picture. Second to the last pic at bottom of page. 

No affiliation...just a picture.



http://www.epi-eng.com/EPI_SrvcTOC.htm



Carlos in AZ

Do not archive



gary wrote:

[quote] 



 I do not have any pix.  It would not be difficult to make one.  It has

 straight side walls that go from the rocker covers straight up.  It goes

 from the rear baffle area arc forward to about 16" above the engine. It has

 reinforcement angles to stiffen the larger panels.



 Sorry I don't know more.   If I get a chance I will try and go over to the

 engine shop and measure.



 Gary

 40274



 --

GRANSCOTT(at)aol.com
Guest

Posted: Fri Nov 30, 2007 1:54 pm Post subject: Engine Choices

I sent a note to Delta Hawk recently...and got this reply from Rip...fyi  for you all...I asked for an update since it's been a few years since I cruised  their site and noticed that they had updated it recently...was wondering if they  were any closer to building and shipping...seem it's the maybe answer...but I  really hope they do deliver in 2008 to someone...

  

 Patrick

  

 Our current work on the DeltaHawk engine is  focused on final testing of production level parts and the endurance testing of  the engine as a unit. That testing has uncovered a couple of issues that were  not evident in some of the previous R&D components. 



As part of  moving towards production, we changed our casting supplier from an R&D level  source to a production level source. Testing has uncovered some unsatisfactory  issues with some parts, and modifications have been made to both design and  process to resolve the problems. We believe we are close to resolution, although  the issue will not be closed until all testing is complete.



The result of  these issues is a slip to our schedule, with the exact amount of slippage not  known until final testing is complete. We will communicate an update to our plan  at that time. We still believe we will be shipping engines in the first half of  2008. 



Thank you for your interest in DeltaHawk engines. If you have  further questions, please let me know.



Sincerely,

Rip  Edmundson

DeltaHawk Engines, Inc.

Racine, Wisconsin  USA

rip(at)deltahawkengines.com



Check out AOL Money & Finance's list of the hottest products and top money wasters of 2007.

  [quote][b]

Tim Olson

Joined: 25 Jan 2007
Posts: 2879

Posted: Fri Nov 30, 2007 1:55 pm Post subject: Engine Choices

Sounds great for the self-overhauler.



The easy way is for the person just buying an engine to have

it run by the place that built it for them.  Aerosport ran

mine as part of their procedures, so when I got it, the timing

was perfect, the fuel flow and pressures were perfect, and

all was well.  They even document it at intervals and

provide you with the paperwork.



But, if you're a DIY guy on the rebuilding, you did just

great.



Tim Olson - RV-10 N104CD - Flying

do not archive

RV10 4JF wrote:

 	  Quote: 	
		   

 

 Hi all,

 

 I've been lurking here for some time. I am hoping to order a tail kit

 at Sun n Fun 08.

 

 When I overhauled my TSIO-520 I made a hood so I could do an on

 aircraft engine run-in, check engine parameters and setup the FI

 pressures. Setting up the pressures is an involved process and time

 consuming.

 

 I made a hood so the engine got proper air flow past the cylinder. In

 my case, I made it out of plywood and metal flashing from Home Depot.

 I then set it on my engine baffles and tied it to the engine. It

 worked pretty well. I followed an article I found on the subject of

 ground running an engine.

 

 I will take a picture tomorrow and see if I can post it.

 

 JF

 

 

 

 

 Read this topic online here:

 

 http://forums.matronics.com/viewtopic.php?p=149634#149634

 

 

 

 

 

 

 

 http://www.matronics.com/Navigator?RV10-List

ricksked(at)embarqmail.co
Guest

Posted: Fri Nov 30, 2007 2:09 pm Post subject: Engine Choices

Thanks for that laugh John, I had a visual of that as I read your post. 

Rick Sked 

40185 do not archive

---

RV10 4JF

Joined: 30 Nov 2007
Posts: 7

Posted: Sat Dec 01, 2007 4:33 pm Post subject: Re: Engine Choices

Attached are a couple of pictures of my homemade engine hood. Plywood sides, 1x and 2x structural wood for the frame and metal flashing. Construction adhesive was used on all mating surfaces, roofing nails for the metal, duck tape and high temp RTV to seal the joints. Simple but effective. It must be securely attached to the engine. I set it on my engine baffles and did my engine run in prior to the engine break in. The article I followed recommends at least Â½ distance from spinner to tip of prop.



BTW,  for my overhaul I have a 3 ring binder where I listed all  part and serial numbers for all components FWF. I also  documented my engine measurements,  run in and break in info. The binder comes in handy if I ever have to research something for a Service Letter, Service Bulletin or AD. He who buys my plane will also get more than just a log book.



JF

IMG_0255.jpg

Description:

Filesize:

121.33 KB

Viewed:

407 Time(s)

IMG_0254.JPG

Description:

Filesize:

44.82 KB

Viewed:

373 Time(s)

IMG_0253.JPG

Description:

Filesize:

39.42 KB

Viewed:

385 Time(s)

Display posts from previous:

	Matronics Email Lists Forum Index -> RV10-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum