Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Saddle, pt II

Matronics Email Lists Forum Index -> Zenith-List

View previous topic :: View next topic

Author Message

naumuk(at)alltel.net
Guest

Posted: Sat Feb 23, 2008 1:05 pm Post subject: Saddle, pt II

All-

     On lister advice, decided to  wait until rear top skins were in place before fitting  the saddle. Rough rigged elevator; will have to pore over ACS catalog  to get electrical fittings to connect tail light, elevator trim, and belly  strobe. Will also have to install a fitting attached to the lower fuse to  support cables. Then I can install the rear fuse top skins.

     Note: HF cable cutting pliers  are a POS. The ACS $15.00 Nico Press squeezer is barely adequate for the  assembly of 1 project. I have 2 fittings to go and the squeezer is about  shot. 

      90% done, 95% to  go!

 Bill Naumuk

Townville, Pa.

HDS  Fuse/Corvair

   [quote][b]

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

dredmoody(at)cox.net
Guest

Posted: Sat Feb 23, 2008 2:21 pm Post subject: Saddle, pt II

For the five conductor trim cable, go to Radio  Shack and buy the panel mount plug for a CB mic. It has five pins and has a  locking ring to keep it securely plugged.

  

 Dred

 [quote]   ---

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

naumuk(at)alltel.net
Guest

Posted: Sat Feb 23, 2008 8:48 pm Post subject: Saddle, pt II

Dred-

     Sounds good. Any pictures?  Wondering about the male connector. 

                                                             Bill

                                 do  not archive

 [quote]   ---

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

dredmoody(at)cox.net
Guest

Posted: Sun Feb 24, 2008 7:37 am Post subject: Saddle, pt II

The plane just moved to the new hangar yesterday. I  had run out of room to continue in my backyard shop. I do not have a decent  photo of the connector. Go to www.radioshack.com and search 4-pin panel mount microphone audio jack. Then search  4-Pin Female CB and HAM Radio Microphone  Plug 4-Pin Female CB and HAM Radio  Microphone Plug . Those two searches will show you the two connectors in  a 4-pin model. I know for a fact (I have three sets of them) that Radio  Shack has a 5-pin version as well. There are other ways to skin this cat but  this connector is one good way.

  

 Dred

  

 ---

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum