Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Aileron integration

Matronics Email Lists Forum Index -> Zenith-List

View previous topic :: View next topic

Author Message

maarten versteeg

Joined: 15 May 2007
Posts: 37
Location: San Antonio

Posted: Thu Feb 28, 2008 5:50 am Post subject: Aileron integration

Hello List,



I am nearing completion of my first wing. My question is when

have you integrated the aileron with the wing. I have already

drilled the flap and aileron to the wing but when should

these be riveted in place. The guide describes holding off on

the flaps till mounting the wings to the plane, but for the

aileron it might be easy to get the bell crank setup and the

trim servo wires attached.

Any advise ?



Maarten

601XL plans building wings.

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

_________________
Maarten Versteeg
601XL scratch building wings

Gig Giacona

Joined: 10 Jan 2006
Posts: 1416
Location: El Dorado Arkansas USA

Posted: Thu Feb 28, 2008 7:09 am Post subject: Re: Aileron integration

I riveted them when I finished the wing long ago. I also installed and ran the trim before I closed up the wing so they are now tangling at the inboard end of the wing with all the other wires.

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

_________________
W.R. "Gig" Giacona
601XL Under Construction
See my progress at www.peoamerica.net/N601WR

Tim Juhl

Joined: 21 Mar 2006
Posts: 488
Location: "Thumb" of Michigan

Posted: Thu Feb 28, 2008 4:48 pm Post subject: Re: Aileron integration

I'm leaving mine off until the wings are installed.  I'm afraid that if I use a sling on the wing with the ailerons in place that I would damage them. Other than that I don't think it matters if you rivet now or later.



Tim



Do not archive

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

_________________
______________
CFII
Champ L16A flying
Zodiac XL - Jabiru 3300A
Almost done! It'll fly in spring!

chris Sinfield

Joined: 28 Nov 2006
Posts: 270
Location: Sydney Australia

Posted: Thu Feb 28, 2008 10:40 pm Post subject: Re: Aileron integration

Thats what Cleco's are for.

Drill and pin the ailerons, put in the cables, belcrank and trim wire, remove and store. 

Chris..

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

Ron Lendon

Joined: 10 Jan 2006
Posts: 685
Location: Clinton Twp., MI

Posted: Fri Feb 29, 2008 7:10 pm Post subject: Re: Aileron integration

Right or wrong my left wing is riveted and hanging from the ceiling with straps. All the plumbing and electrical is in and functioning.

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

AileronFlap 005.jpg

Description:

Fixture to hold flap and aileron together. The ty-wrap goes around the head of the bolt on the aileron and pulls the wedge forward.

Filesize:

154.4 KB

Viewed:

446 Time(s)

HangWing 003.jpg

Description:

Filesize:

188.14 KB

Viewed:

442 Time(s)

_________________
Ron Lendon
WW Corvair with Roy's Garage 5th bearing
CH 601 XLB
N601LT - Flying
http://www.mykitlog.com/rlendon
Corvair Engine Prints:
https://sites.google.com/site/corvairenginedata/

psm(at)att.net
Guest

Posted: Sat Mar 01, 2008 3:57 am Post subject: Aileron integration

Hi Tim,



I went ahead and riveted my ailerons when I built the wings.  For 

storage and moving around, I attached a few sticks across the 

ailerons to the wing skin using duct tape.  Each stick is around 1 

foot long and perhaps 1 inch by 1/4 inch cross section.  Actual size 

of the sticks is random.



I store the wings with the nose ribs facing down.  They are in little 

carts made with harbor freight wheels and plywood from the Zenith 

shipping crates.  This doesn't put any load on the ailerons.

Paul

XL fuselage

do not archive

At 04:48 PM 2/28/2008, you wrote:



 	  Quote: 	
		  I'm leaving mine off until the wings are installed.  I'm afraid that 

if I use a sling on the wing with the ailerons in place that I would 

damage them. Other than that I don't think it matters if you rivet 

now or later.



Tim

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

naumuk(at)alltel.net
Guest

Posted: Sat Mar 01, 2008 6:16 am Post subject: Aileron Integration

Tim-

     Since I'm polishing, I left the  ailerons clecoed to the wings so I could polish them before making cuts to  install the aileron trim.

     My storage rack is the same  basic concept as Paul's or Larry Macs- nose down. 

     My wife's aunt said "Anybody  want an old entertainment center?" and it hit me. Take the doors off, put  casters on the back corners, cut cradle openings and line them with water  pipe insulation and you're done- 3 hours build time shown in my log.  Total outlay less than $15 for bed casters and a bag of pipe  insulation.

     This is an old picture- all  assemblies I've brought upstairs over the years have shown no ill effects from  storage in this manner. If you have curious little kids or big dogs you might  want to go with the overhead option.

                                       do not  archive

 Bill Naumuk

Townville, Pa.

HDS  Fuse/Corvair

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

OTHER_STUFF.jpg

Description:

Filesize:

124.26 KB

Viewed:

427 Time(s)

Tim Juhl

Joined: 21 Mar 2006
Posts: 488
Location: "Thumb" of Michigan

Posted: Sat Mar 01, 2008 6:53 am Post subject: Re: Aileron integration

You guys have all found good solutions to the storage issue.  In my case, I'm hanging them from the rafters in my hangar (at home) using lengths of rejected seatbelt webbing.  I hung them nose up with wood blocks set in the rear spar channel to distribute the forces.



Someone on the group described using a shop crane and sling to support the wing while fitting it to the fuselage.  Knowing my luck I just figured I'd damage something if I left the control surfaces on while trying something like that. If I was sure I'd have enough help on hand I wouldn't worry about it.  I fit the flaps and ailerons beforehand, so all I did was pull the hinge pin on the flaps and de-cleco the ailerons.  All the wiring & etc (less control cables) is in the wings and the aileron pushrods are pretty close to desired length.  Hopefully it won't be a big deal to do the final installation.



Tim



Do not archive

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

HangingWing.jpg

Description:

Filesize:

29.9 KB

Viewed:

423 Time(s)

_________________
______________
CFII
Champ L16A flying
Zodiac XL - Jabiru 3300A
Almost done! It'll fly in spring!

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum