|
Matronics Email Lists Web Forum Interface to the Matronics Email Lists
|
View previous topic :: View next topic |
Author |
Message |
kregg(at)balancemyprop.co Guest
|
Posted: Tue Apr 15, 2008 7:52 am Post subject: Yak52 Cowling Shutter axle/pivot Screws |
|
|
If anyone needs the long shutter axle(pivot) screw for a -52. They seem to wear on the screw head end and will eventually wear into. I had to have some made, and have extras. They are made from high quality treated stainless steel and will last for a long time. They are $17.62 each. Also, does anyone have the shorter screws at the base of the shutters?
Thanks,
Kregg Victory
| - The Matronics Yak-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
Description: |
|
Filesize: |
282.41 KB |
Viewed: |
385 Time(s) |
|
|
|
Back to top |
|
|
Dale
Joined: 30 May 2007 Posts: 178
|
Posted: Sun Apr 20, 2008 5:35 pm Post subject: Re: Yak52 Cowling Shutter axle/pivot Screws |
|
|
All of those screws can be made out of metric cap screws by adding thread and cross drilling the head. About 50 cents each. There are two different lengths.
| - The Matronics Yak-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
|
|
Back to top |
|
|
KingCJ6(at)AOL.COM Guest
|
Posted: Sun Apr 20, 2008 7:30 pm Post subject: Yak52 Cowling Shutter axle/pivot Screws |
|
|
Was there a previous post on this topic? We are in constant need of shutter maintenence/repalcement.
In a message dated 4/20/2008 6:38:39 P.M. Pacific Daylight Time, hdinamic(at)qwest.net writes:
Quote: | --> Yak-List message posted by: "Dale" <hdinamic(at)qwest.net>
All of those screws can be made out of metric cap screws by adding thread and cross drilling the head. About 50 cents each.
|
Need a new ride? Check out the largest site for U.S. used car listings at AOL Autos.
[quote][b]
| - The Matronics Yak-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
|
|
Back to top |
|
|
kregg(at)balancemyprop.co Guest
|
Posted: Mon Apr 21, 2008 7:05 am Post subject: Yak52 Cowling Shutter axle/pivot Screws |
|
|
Dale,
I would like to buy 500 from you at 50 cents each. They need to be made
from treated stainless steel. Please send a sample for me to approve to:
Victory Aero
2502 John Montgomery Drive
San Jose, CA 95148
Thanks,
Kregg Victory
408-729-7635
--
| - The Matronics Yak-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
|
|
Back to top |
|
|
schrick(at)pacbell.net Guest
|
Posted: Mon Apr 21, 2008 8:22 am Post subject: Yak52 Cowling Shutter axle/pivot Screws |
|
|
Dale,
You have got to be kidding!!!!!!! Jill charges $19 each for steel ones and the time and labor to produce is higher than that. She has these in stock and Craig has taken the time to improve the Russian desgn. If you can truly pruduce these for $0.50 each. I need 27 of them to replace my russian steel ones with your stainless steel 50 cent part.
Where do I send the check?
I am ready to purchase today. Can you have them ready by this Friday? Saturday?
Looking forward to receiving my 50 cent each cowling shutter axle/ pivot screws and rods you promised.
SHREK
PLEASE..................
[quote][b]
| - The Matronics Yak-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
|
|
Back to top |
|
|
Dale
Joined: 30 May 2007 Posts: 178
|
Posted: Mon Apr 21, 2008 6:54 pm Post subject: Re: Yak52 Cowling Shutter axle/pivot Screws |
|
|
The short screws on the shutter bottom can be made out of cap screws. I did not mention the long pivot screws so don't get excited. I am talking about the screws that are about 6 and 8mm long. I did not say I would do it for you. I made them for myself at a cost of 50 cents. Jill does not have any in stock so I made my own. I am only pointing out what alternatives can be used for some of the parts. I am sorry I fueled the sarcasm.
| - The Matronics Yak-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
|
|
Back to top |
|
|
kregg(at)balancemyprop.co Guest
|
Posted: Tue Apr 22, 2008 7:01 am Post subject: Yak52 Cowling Shutter axle/pivot Screws |
|
|
No Problem at all here. I am having a hard time finding those screws as
well, so I have a machine shop make the for me. I will take 500 of the
shutter bottom attach screws too. Would you be willing to make some?
Thanks,
Kregg
--
| - The Matronics Yak-List Email Forum - | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Yak-List |
|
|
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|