 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
Jaybannist(at)cs.com
Guest
|
 Posted: Mon Apr 28, 2008 10:49 am Post subject: Flap Stop |
 |
|
Lance, Here 'tis. Jay in Dallas
"lgingell" <lgingell(at)matrix-logic.com> wrote:
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
| Description: |
|
Download |
| Filename: |
FlapStop.pdf |
| Filesize: |
38.89 KB |
| Downloaded: |
447 Time(s) |
|
|
| Back to top |
|
 |
lgingell
Joined: 10 Jan 2006
Posts: 50
Location: Lake California Airpark 68CA
|
| Posted: Mon Apr 28, 2008 9:42 pm Post subject: Re: Flap Stop |
|
|
Thanks Jay. What date are your plans?
Cheers,
..lance
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
_________________
Zodiac XL/Jab 3300
http://lancegingell.com |
|
| Back to top |
|
|
maarten versteeg
Joined: 15 May 2007
Posts: 37
Location: San Antonio
|
| Posted: Tue Apr 29, 2008 11:54 am Post subject: Flap stop |
|
|
Hello Tim,
I don't know if a second stop would improve the flap stabilization
in the up position. Having only a single stop at the outboard end
and having the inboard end being pushed up by the control pin may
do a better job in placing the flap in a locked position. By adding
a third point one of the support points won't be held snug since
the flap is over constrained. You may want to make sure that the
inboard flap stop is the shortest and only prevents the flap
from being overstretched but the material springiness should hold
the flap between outboard stop and the inboard pin.
Regards,
Maarten
601xl plans building first wing, marked the flap stop position as
no rivet zone.
> >
> > Flap Stop comment - The nylon stop does a good job of preventing
movement
> > of the retracted flap at the outboard end, while the inboard end is
> > restrained by the actuating pin which rests in a slot. I am
considering
> > installing a second stop at the inboard end to make it even more solid.
> >
> > Comments?
> >
> > Tim
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
_________________
Maarten Versteeg
601XL scratch building wings |
|
| Back to top |
|
|
Jaybannist(at)cs.com
Guest
|
| Posted: Tue Apr 29, 2008 12:41 pm Post subject: Flap Stop |
|
|
Lance,
My plans are dated August 25, 2005, marked up with Rev. 3, 3/15/06.
Jay in Dallas
Do not archive
"lgingell" <lgingell(at)matrix-logic.com> wrote:
| | - The Matronics Zenith-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
