 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
Thruster87
Joined: 16 Apr 2008
Posts: 193
Location: Australia
|
 Posted: Mon Jun 09, 2008 10:53 pm Post subject: Elevator Trim tab motor |
 |
|
The trim tab motor does not line up with the access hole [factory cutout] once the rod is approximately in the center of the cutout [20 -25mm out towards the i/b side].If one was to mount the motor onto the bottom skin instead then it does line up, because of the offset on the trim motor actuator.My question ? is there a r/h and a l/h version of the trim motor. Cheers
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
 |
Afterfxllc(at)aol.com
Guest
|
| Posted: Tue Jun 10, 2008 2:43 am Post subject: Elevator Trim tab motor |
|
|
I just installed mine and it was offset also but you can still get at it if you had to. The motor is about 30mm from the rib and the rivets are about 20mm from the rib.
Jeff
Vote for your city's best dining and nightlife. City's Best 2008.
[quote][b]
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
|
Jaybannist(at)cs.com
Guest
|
| Posted: Tue Jun 10, 2008 4:38 am Post subject: Elevator Trim tab motor |
|
|
Cheers,
Yes, there are left and right hand trim servos. I had the same problem as you are describing. After discussing it with ZAC, I cut a larger access hole and made a larger cover.
Jay in Dallas
"Thruster87" <alania(at)optusnet.com.au> wrote:
| Quote: |
The trim tab motor does not line up with the access hole [factory cutout] once the rod is approximately in the center of the cutout [20 -25mm out towards the i/b side].If one was to mount the motor onto the bottom skin instead then it does line up, because of the offset on the trim motor actuator.My question ? is there a r/h and a l/h version of the trim motor. Cheers
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=187089#187089
|
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
|
countzero
Joined: 25 Oct 2007
Posts: 25
|
| Posted: Tue Jun 10, 2008 4:58 am Post subject: Re: Elevator Trim tab motor |
|
|
My pre-cut Elevator access hole was offset from the servo body and lined up with the rod instead.
I found that the Aileron access hole lined-up with the servo body after I made the cutout as per the drawing dimensions but then it was slightly harder to access the clevis to install the pin, clip and washers.
Rob
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
|
cndmovn(at)gmail.com
Guest
|
| Posted: Tue Jun 10, 2008 5:14 am Post subject: Elevator Trim tab motor |
|
|
Did mine exactly like Jeff's. the pictures in the manual show it offset from the access panel in a few of the pics.
On Tue, Jun 10, 2008 at 6:43 AM, <Afterfxllc(at)aol.com (Afterfxllc(at)aol.com)> wrote:
[quote] I just installed mine and it was offset also but you can still get at it if you had to. The motor is about 30mm from the rib and the rivets are about 20mm from the rib.
Jeff
Vote for your city's best dining and nightlife. City's Best 2008.
[b]
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
|
BobTezyk
Joined: 10 Jan 2006
Posts: 38
Location: Midlothian, TX
|
| Posted: Tue Jun 10, 2008 8:04 pm Post subject: Re: Elevator Trim tab motor |
|
|
Here are some pictures of my QBK servo installation. I had no problem with getting the servo lined up.
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
| Description: |
|
| Filesize: |
82.2 KB |
| Viewed: |
711 Time(s) |
|
| Description: |
|
| Filesize: |
53.77 KB |
| Viewed: |
707 Time(s) |
|
| Description: |
|
| Filesize: |
115.49 KB |
| Viewed: |
697 Time(s) |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
