 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
Matt Dralle
Site Admin
Joined: 08 Nov 2005
Posts: 26320
Location: Livermore CA USA
|
 Posted: Sat May 09, 2009 9:49 am Post subject: Mounting Antennas On Bottom Fuselage Skin... |
 |
|
Fellow Builders,
I'm getting ready to mount the COM (Commant bent whips) and Transponder (Commant shark fin) antennas on the bottom of the RV-8. I plan to mount them to the bottom fuselage skin right behind the aileron torque tubes. I think this is something like .040" skin and its pretty rigid, but what are people's thoughts on adding a skin doubler, perhaps a .032 piece something like 6"x8"? I'd rather not, but on the other hand, I don't want to have the skin end up deformed over time.
Thanks in advance.
Matt Dralle
RV-8 #82882 N998RV
Laying Out Carpet in CAD...
| | - The Matronics RV8-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV8-List |
|
_________________
Matt Dralle
Matronics Email List Administrator |
|
| Back to top |
|
 |
jim-bean(at)att.net
Guest
|
| Posted: Sat May 09, 2009 10:51 am Post subject: Mounting Antennas On Bottom Fuselage Skin... |
|
|
| | - The Matronics RV8-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV8-List |
|
|
|
| Back to top |
|
|
carl.froehlich(at)verizon
Guest
|
| Posted: Sat May 09, 2009 11:12 am Post subject: Mounting Antennas On Bottom Fuselage Skin... |
|
|
I believe the skin is 0.032" not 0.040".
Recommend using a 0.032' doubler. 6"x8" is larger than needed however.
Consider something that extends and inch or two beyond the antenna mounting
screws. A simple install is a little bit of pro-seal between the doubler
and the skin, and then the antenna hardware through both the skin and the
doubler. Don't be concerned that you do not have perfect metal to metal
connection. The antenna needs an RF ground, not a DC ground. As long as it
is mounted on the skin you are ok, even if you have primer/paint on the
skin.
Put some spacing between the two antennas, perhaps a couple of feet.
Carl Froehlich
RV-8A (475 hrs)
RV-10 (fuselage)
--
| | - The Matronics RV8-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV8-List |
|
|
|
| Back to top |
|
|
rv8builder
Joined: 02 Jan 2009
Posts: 56
|
| Posted: Sat May 09, 2009 6:24 pm Post subject: Mounting Antennas On Bottom Fuselage Skin... |
|
|
In my crude survey of other builders, I discovered that 2/3 or more of builders do put a doubler plate on the inside of the bottom skin for at least the comm antenna. As you suggested, about a 6 x 8 inch piece of .032 material. But I suspect that a 6 x 6 piece would work, if that is what you happen to have laying around.
I have seen that doubler riveted with both countersunk and universal head rivets.
Dale
--
| | - The Matronics RV8-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV8-List |
|
_________________
Dale |
|
| Back to top |
|
|
vshimsl(at)live.com
Guest
|
| Posted: Sat May 09, 2009 6:41 pm Post subject: Mounting Antennas On Bottom Fuselage Skin... |
|
|
Used same antennae C same location except transponder was near rear bellcrank. Both areas I used a doubler.
Vince H.
RV-8 N8432
Preparing for inspection.
Windows Live™: Keep your life in sync. Check it out. [quote][b]
| | - The Matronics RV8-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV8-List |
|
|
|
| Back to top |
|
|
madman266(at)comcast.net
Guest
|
| Posted: Sat May 09, 2009 7:39 pm Post subject: Mounting Antennas On Bottom Fuselage Skin... |
|
|
if you bend up 1/4 in on each side, the stiffener will be more stiff .. j
| | - The Matronics RV8-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV8-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
