 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
Bill Schlatterer
Joined: 09 Jan 2006
Posts: 195
|
 Posted: Sat Jul 25, 2009 5:17 pm Post subject: Conduit Placement in QB RV7 Wings |
 |
|
Can't decide if this is a good thing to do or not. I need to run conduit in my QB wings but there are no consistent tooling holes anywhere except where Vans put the pitot holes and the one tooling hole above that. (actually below if the wing is right side up).
It would be pretty easy to put a 3/4 hole in place of the pitot holes and in the tooling holes above with a 3/4 step drill and a 4 foot extension but it would get pretty close to the spar. Is there an edge distance issue with this or does it even apply? Doing it anywhere else without the tooling holes is problematic?
Any comments, suggestions, pictures appreciated. <<...>>
Bill S
RV7 only the wings left,….
| | - The Matronics RV7-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV7-List |
|
| Description: |
|
| Filesize: |
68.87 KB |
| Viewed: |
4434 Time(s) |
|
|
|
| Back to top |
|
 |
Tim B
Joined: 07 Sep 2006
Posts: 32
Location: Denver, NC
|
| Posted: Sat Jul 25, 2009 6:52 pm Post subject: Conduit Placement in QB RV7 Wings |
|
|
Bill,
I'm still deciding what path to take myself. Here's another idea that I found online that may interest you.
Tim Bolton
Denver, NC
RV-7 (#72696)
www.TheRV7.com
[img]cid:010301ca0d9a$6403a8c0(at)PYS[/img]
[img]cid:010401ca0d9a$6403a8c0(at)PYS[/img]
[img]cid:010501ca0d9a$6403a8c0(at)PYS[/img]
| | - The Matronics RV7-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV7-List |
|
| Description: |
|
| Filesize: |
86.44 KB |
| Viewed: |
4434 Time(s) |
|
| Description: |
|
| Filesize: |
71.01 KB |
| Viewed: |
4434 Time(s) |
|
| Description: |
|
| Filesize: |
65.67 KB |
| Viewed: |
4434 Time(s) |
|
_________________
Tim Bolton
Denver, NC |
|
| Back to top |
|
|
snoopyflys
Joined: 17 May 2009
Posts: 1
Location: Katy, Texas
|
| Posted: Sat Jul 25, 2009 6:55 pm Post subject: Conduit Placement in QB RV7 Wings |
|
|
Hi Bill,
I am working on slow build wings and have drilled ¾ inch holes in the aft tooling hole and just aft of the larger lighting hole near the top skin. This will give me the ability to run antenna wires, lights, etc. with minimal to no EMI. Here is a link to Van’s recommended location http://www.vansaircraft.com/pdf/Wing_Wiring.pdf if you haven’t already viewed it.
Regards,
Dan
From: owner-rv7-list-server(at)matronics.com [mailto:owner-rv7-list-server(at)matronics.com] On Behalf Of Bill Schlatterer
Sent: Saturday, July 25, 2009 8:14 PM
To: rv7-list(at)matronics.com; RV7A(at)yahoogroups.com; rv-list(at)matronics.com; RV9-list(at)matronics.com
Subject: Conduit Placement in QB RV7 Wings
Can't decide if this is a good thing to do or not. I need to run conduit in my QB wings but there are no consistent tooling holes anywhere except where Vans put the pitot holes and the one tooling hole above that. (actually below if the wing is right side up).
It would be pretty easy to put a 3/4 hole in place of the pitot holes and in the tooling holes above with a 3/4 step drill and a 4 foot extension but it would get pretty close to the spar. Is there an edge distance issue with this or does it even apply? Doing it anywhere else without the tooling holes is problematic?
Any comments, suggestions, pictures appreciated. <<...>>
Bill S
RV7 only the wings left,….
[quote][b]
| | - The Matronics RV7-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV7-List |
|
_________________
Dan Schultz
RV-7A
Wings - Tanks |
|
| Back to top |
|
|
Jon Hussey
Joined: 11 Oct 2007
Posts: 3
|
| Posted: Sat Jul 25, 2009 7:10 pm Post subject: Conduit Placement in QB RV7 Wings |
|
|
[quote] ---
| | - The Matronics RV7-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV7-List |
|
| Description: |
|
Download |
| Filename: |
Wing_Wiring.pdf |
| Filesize: |
9.47 KB |
| Downloaded: |
485 Time(s) |
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
