 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
Matt Dralle
Site Admin
Joined: 08 Nov 2005
Posts: 25781
Location: Livermore CA USA
|
 Posted: Mon Jul 27, 2009 3:26 pm Post subject: Hooker Rotary Harness Installation |
 |
|
Dear Listers,
I was looking at how the Hooker Harnesses were going to be installed and noticed that the triangle mounting pieces have a small, "bushing" in the hole where the bolt goes. The triangle piece is already about twice the thickness of Vans standard belts and its a tight fit to get them squeezed into the mounting forks. But with the bushing in there it seems impossible. Are you suppose to just remove the bushing, or some how mash it down? I don't get it...
Thanks!
Matt Dralle
RV-8 #82880 N998RV
| | - The Matronics RV-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV-List |
|
| Description: |
|
| Filesize: |
398.38 KB |
| Viewed: |
1810 Time(s) |
|
_________________
Matt Dralle
Matronics Email List Administrator |
|
| Back to top |
|
 |
mrobert569(at)hotmail.com
Guest
|
| Posted: Mon Jul 27, 2009 7:13 pm Post subject: Hooker Rotary Harness Installation |
|
|
Matt C
You can take the bushings out of the mount. Just make sure you don't crank down too tight on the bolts. The triangles shoudl pivot freely in the airframe mounts.
Mike Robertson
Das Fed
[quote] Date: Mon C 27 Jul 2009 16:23:46 -0700
To: rv-list(at)matronics.com
From: dralle(at)matronics.com
Subject: Hooker Rotary Harness Installation
Dear Listers C
I was looking at how the Hooker Harnesses were going to be installed and noticed that the triangle mounting pieces have a small C "bushing" in the hole where the bolt goes. The triangle piece is already about twice the thickness of Vans standard belts and its a tight fit to get them squeezed into the mounting forks. But with the bushing in there it seems impossible. Are you suppose to just remove the bushing C or some how mash it down? I don't get it...
Thanks!
Matt Dralle
RV-8 #82880 N998RV
NEW mobile Hotmail. Optimized for YOUR phone. Click here.
| | - The Matronics RV-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV-List |
|
|
|
| Back to top |
|
|
Michael Wynn
Joined: 10 Jan 2006
Posts: 148
Location: San Ramon, CA
|
| Posted: Tue Jul 28, 2009 4:28 pm Post subject: Hooker Rotary Harness Installation |
|
|
Hi Matt,
I just discussed this very subject with the Hooker rep at Osh. He said to use a file or scotchbrite wheel to flatten it as much as necessary to fit in. I haven't really dealt with the issue first hand, but that is what they are telling me.
Regards,
Michael Wynn
RV 8 Finishing
San Ramon, CA
In a message dated 7/27/2009 3:30:39 P.M. Pacific Standard Time, dralle(at)matronics.com writes:
| Quote: |
Dear Listers,
I was looking at how the Hooker Harnesses were going to be installed and noticed that the triangle mounting pieces have a small, "bushing" in the hole where the bolt goes. The triangle piece is already about twice the thickness of Vans standard belts and its a tight fit to get them squeezed into the mounting forks. But with the bushing in there it seems impossible. Are you suppose to just remove the bushing, or some how mash it down? I don't get it...
Thanks!
Matt Dralle
RV-8 #82880 N998RV
|
A Good Credit Score is 700 or Above. See yours in just 2 easy steps!
[quote][b]
| | - The Matronics RV-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV-List |
|
_________________
Michael Wynn
RV 8
San Ramon, CA |
|
| Back to top |
|
|
Bret Smith
Joined: 09 Jan 2006
Posts: 178
Location: Mineral Bluff, GA
|
| Posted: Tue Jul 28, 2009 6:10 pm Post subject: Hooker Rotary Harness Installation |
|
|
Matt,
I just took the bushing to the grinder and ground it down until it fit nice and snug.
Bret Smith
RV-9A N16BL
Blue Ridge, Ga
www.FlightInnovations.com
From: owner-rv-list-server(at)matronics.com [mailto:owner-rv-list-server(at)matronics.com] On Behalf Of Tailgummer(at)aol.com
Sent: Tuesday, July 28, 2009 8:50 PM
To: rv-list(at)matronics.com
Subject: Re: Hooker Rotary Harness Installation
Matt,
I removed the existing bushing and replaced it with a flush bushing custom fit to the width of the triangular connector. Left is harness with Hooker factory bushing, center shows custom made bushing to fit into right steel harness connector:
[img]cid:122590202(at)29072009-129E[/img]
This will allow the Hooker steel connector to fit into Van's clevis quite easily.
John D
| | - The Matronics RV-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV-List |
|
| Description: |
|
| Filesize: |
50.25 KB |
| Viewed: |
1804 Time(s) |
|
_________________
Bret Smith
RV-9A (Emp) |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
