 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
MauleDriver(at)nc.rr.com
Guest
|
 Posted: Fri Aug 14, 2009 5:12 pm Post subject: Oil door hidden hinge |
 |
|
Well, I screwed up the FAB and have to re-order the top plate so on to
the oil door...
I have the hidden hinge and am ready to attach to cowl. But I'm
concerned about what fastener to use to go through the honey combed
strips surrounding the oil door cutout.
There seems to be thin honeycomb throughout the cowl but there is a
strip of slightly thicker honeycomb around the edge of the cowl and
surrounding the oil door cutout. After drilling it, It became clear it
is 'hollow'.
So I'm concerned that rivets will not work well. I'm thinking something
like 4-40 flat head screws (with the heads overlayed with glass. Or
perhaps I need to fill the honeycomb with flock then drill. Or cut it
out and fill.
I think the standard door hinges are attached where there isn't any
honeycomb, inside the square of honecomb surrounding the cutout.
Any thoughts?
Bill "FWF" Watson
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
 |
Ron B.
Joined: 17 Feb 2009
Posts: 103
Location: Nova Scotia
|
| Posted: Fri Aug 14, 2009 5:18 pm Post subject: Re: Oil door hidden hinge |
|
|
I removed the core and layed up solid epoxy and glass. Be careful as the outer skin is very thin.
Ron
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
dave.saylor.aircrafters(a
Guest
|
| Posted: Fri Aug 14, 2009 7:54 pm Post subject: Oil door hidden hinge |
|
|
Good instincts, Bill. Replace the honeycomb with flox/resin to make a hard point and it should last forever.
Dave
On Fri, Aug 14, 2009 at 5:48 PM, Bill Mauledriver Watson <MauleDriver(at)nc.rr.com (MauleDriver(at)nc.rr.com)> wrote:
| Quote: | --> RV10-List message posted by: Bill Mauledriver Watson <MauleDriver(at)nc.rr.com (MauleDriver(at)nc.rr.com)>
Well, I screwed up the FAB and have to re-order the top plate so on to the oil door...
I have the hidden hinge and am ready to attach to cowl. But I'm concerned about what fastener to use to go through the honey combed strips surrounding the oil door cutout.
There seems to be thin honeycomb throughout the cowl but there is a strip of slightly thicker honeycomb around the edge of the cowl and surrounding the oil door cutout. After drilling it, It became clear it is 'hollow'.
So I'm concerned that rivets will not work well. I'm thinking something like 4-40 flat head screws (with the heads overlayed with glass. Or perhaps I need to fill the honeycomb with flock then drill. Or cut it out and fill.
I think the standard door hinges are attached where there isn't any honeycomb, inside the square of honecomb surrounding the cutout.
Any thoughts?
Bill "FWF" Watson
===========
arget="_blank">http://www.matronics.com/Navigator?RV10-List
===========
http://forums.matronics.com
===========
le, List Admin.
="_blank">http://www.matronics.com/contribution
===========
|
--
Dave Saylor
AirCrafters LLC
140 Aviation Way
Watsonville, CA 95076
831-722-9141 Shop
831-750-0284 Cell
[quote][b]
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
ivankris
Joined: 29 May 2009
Posts: 21
Location: Guelph, Ontario. Canada
|
| Posted: Sat Aug 15, 2009 10:19 am Post subject: Re: Oil door hidden hinge |
|
|
YOU shouldn't need to get into the honeycomb areas of the top cowl to attach a hidden hinge here is a link to some pictures I hope will help you understand the process. http://ivankristensen.phanfare.com/2292606_4268126#imageID=77306227
This hidden hinge and the door latches are from Non Stop Aviation
Regards,
Ivan Kristensen
#40838
FF and wiring
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
MauleDriver(at)nc.rr.com
Guest
|
| Posted: Sat Aug 15, 2009 2:11 pm Post subject: Oil door hidden hinge |
|
|
Thanks for the pics. Yes, I thought that's what I would be doing but
I've already cut too big a hole and am planning a slightly larger door
and door opening. Note to self; cut a small hole then enlarge as more
is learned.
Nice site and pics. Thanks!
vankris wrote:
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
hotwheels
Joined: 01 Jun 2007
Posts: 240
|
| Posted: Sun Aug 16, 2009 8:23 pm Post subject: Re: Oil door hidden hinge |
|
|
Bill,
I cut a bit too much off on the inboard side also. It was pretty easy to just glass what was needed back on... Not a big deal. I left a lip all the way around. The door turned out nice. Be sure to reinforce the latch side cowl lip as there's not a lot of grip area.
http://www.brinkmeyers.net/Photos/Aircraft/Engine/images/imag0095.jpg
Jay
| MauleDriver(at)nc.rr.com wrote: | Thanks for the pics. Yes, I thought that's what I would be doing but
I've already cut too big a hole and am planning a slightly larger door
and door opening. Note to self; cut a small hole then enlarge as more
is learned.
Nice site and pics. Thanks!
vankris wrote:
|
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
jump2(at)sbcglobal.net
Guest
|
| Posted: Mon Aug 17, 2009 3:44 am Post subject: Oil door hidden hinge |
|
|
You might want to consider putting a couple of metal strips where the cam lock locks on the cowling due to the fact it will vibrate and wear away the composite over time..
Just a thought.
Patrick Thyssen
flying when electrons let me.
--- On Sun, 8/16/09, jayb <jaybrinkmeyer(at)yahoo.com> wrote:
| Quote: |
From: jayb <jaybrinkmeyer(at)yahoo.com>
Subject: RV10-List: Re: Oil door hidden hinge
To: rv10-list(at)matronics.com
Date: Sunday, August 16, 2009, 11:23 PM
--> RV10-List message posted by: "jayb" <[url=/mc/compose?to=jaybrinkmeyer(at)yahoo.com]jaybrinkmeyer(at)yahoo.com[/url]>
Bill,
I cut a bit too much off on the inboard side also. It was pretty easy to just glass what was needed back on... Not a big deal. I left a lip all the way around. The door turned out nice. Be sure to reinforce the latch side cowl lip as there's not a lot of grip area.
http://www.brinkmeyers.net/Photos/Aircraft/Engine/images/imag0095.jpg
Jay
MauleDriver(at)nc.rr.com wrote:
| Quote: | Thanks for the pics. Yes, I thought that's what I would be doing but
I've already cut too big a hole and am planning a slightly larger door
and door opening. Note to self; cut a small hole then enlarge as more
is learned.
Nice site and pics. Thanks!
vankris wrote:
>
>
> YOU shouldn't need to get into the honeycomb areas of the top cowl to attach a hidden hinge here is a link to some pictures I hope will help you understand the process. http://ivankristensen.phanfare.com/2292606_4268126#imageID=77306227
> This hidden hinge and the door latches are from Non Stop Aviation
>
> Regards,
>
> Ivan Kristensen
>
> #40838
>
> FF and wiring
>
>
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p 57821#257821
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
|
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=25813onics.com/Navigator?RV10-List" target="_blank">http://www.matronics.com/N= - MATRONICS t; http://forums.sp; - List Contribution Web Sbsp; > ht
|
[quote][b]
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
AirMike
Joined: 27 Feb 2007
Posts: 514
Location: Nevada
|
| Posted: Mon Aug 17, 2009 4:26 am Post subject: Oil door hidden hinge |
|
|
Added some extra glass and a Z-bar stiffener and it seems to work well.
Should have taken the time for the 100% hidden door, but at least it is flush and do not have the do-hickers sticking up.
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
| Description: |
|
| Filesize: |
546.98 KB |
| Viewed: |
6761 Time(s) |
|
_________________
See you OSH '18
Q/B - sold. |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
