Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

601XL Cowling

Matronics Email Lists Forum Index -> Zenith-List

View previous topic :: View next topic

Author Message

vk3eka(at)bigpond.net.au
Guest

Posted: Fri Aug 28, 2009 10:38 pm Post subject: 601XL Cowling

Hi Guys,  

   

I received my camlocs for the cowling from ASSC the other day.  

   

Attached is a photo. The photo shows:-  

   

40S5-3S SS CAMLOC STUD       	  Quote: 	
		  4002-NS CAMLOC GROMMET            214-16ND CAMLOC 4002 Receptacle 	
  

   

How do I get the stud into the grommet. Do I have to remove the pin? If so, how?  

   

Cheers  

   

Peter  

Wonthaggi Australia  

http://zodiac.cpc-world.com  

   

    	  Quote:

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

IMG_1331.JPG

Description:

Filesize:

504.63 KB

Viewed:

3075 Time(s)

vk3eka(at)bigpond.net.au
Guest

Posted: Fri Aug 28, 2009 11:22 pm Post subject: 601XL Cowling

Craig,  

   

Thanks for that.  

   

A pair of needle nose pliers did the same thing. I was looking for a complicated solution to what is a simple problem.  

   

Thanks  

   

Peter  

   

   

       

From: owner-zenith601-list-server(at)matronics.com [mailto:owner-zenith601-list-server(at)matronics.com] On Behalf Of Craig Payne

 Sent: Saturday, 29 August 2009 5:08 PM

 To: zenith601-list(at)matronics.com

 Subject: RE: 601XL Cowling  

  

  

   

I haven’t used the grommets on mine but this is how I get the camloc studs through the holes I drill. Compress the camloc and its spring with the special camloc pliers. Then you should be able to “hook” the shaft with the pin through the grommet. Try this document:  

   

www.afscamloc.net/xua/downloads/Camloc%20Quick%20Release%20Fasteners.pdf  

   

-- Craig  

       

From: owner-zenith601-list-server(at)matronics.com [mailto:owner-zenith601-list-server(at)matronics.com] On Behalf Of Peter W Johnson

 Sent: Saturday, August 29, 2009 12:38 AM

 To: zenith-list(at)matronics.com; zenith601-list(at)matronics.com

 Subject: 601XL Cowling  

  

  

   

Hi Guys,  

   

I received my camlocs for the cowling from ASSC the other day.  

   

Attached is a photo. The photo shows:-  

   

40S5-3S SS CAMLOC STUD       	  Quote: 	
		  4002-NS CAMLOC GROMMET            214-16ND CAMLOC 4002 Receptacle 	
  

   

How do I get the stud into the grommet. Do I have to remove the pin? If so, how?  

   

Cheers  

   

Peter  

Wonthaggi Australia  

http://zodiac.cpc-world.com  

   

    	  Quote: 	
		    	
  

    	  Quote: 	
		    214-16ND CAMLOC 4002 Receptacle 	
0 	  Quote: 	
		  214-16ND CAMLOC 4002 Receptacle 	
1 	  Quote: 	
		  214-16ND CAMLOC 4002 Receptacle 	
2 	  Quote: 	
		  214-16ND CAMLOC 4002 Receptacle 	
3 	  Quote: 	
		  214-16ND CAMLOC 4002 Receptacle 	
4 	  Quote: 	
		  214-16ND CAMLOC 4002 Receptacle 	
5 	  Quote: 	
		  214-16ND CAMLOC 4002 Receptacle 	
6 	  Quote: 	
		  214-16ND CAMLOC 4002 Receptacle 	
7 	  Quote: 	
		  214-16ND CAMLOC 4002 Receptacle 	
8 	  Quote: 	
		  214-16ND CAMLOC 4002 Receptacle 	
9 	  Quote: 	
		   	
0 	  Quote: 	
		   	
1 	  Quote: 	
		   	
2 	  Quote: 	
		   	
3

       [quote][b]

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

maarten versteeg

Joined: 15 May 2007
Posts: 37
Location: San Antonio

Posted: Sat Aug 29, 2009 5:12 am Post subject: 601XL Cowling

Hello,



Camlocs can just be inserted in the grommet by compressing the 

spring and then it will fit through the hole. There are special

pliers available, but I just took a little strip of steel and

made a cutout at one end that can support the camloc under the 

flange, then by holding the steel piece in your hand you can now

easily push on the head of the camloc and compress the spring and

then maneuver it through the grommet or aluminum plate. I can

send you a picture of the little tool if this is not clear but I

am on the road at this moment.



Maarten, 601XL, plans build

 	  Quote: 	
		   Hi Guys,



 I received my camlocs for the cowling from ASSC the other day.

 Attached is a photo. The photo shows:-



 40S5-3S SS CAMLOC STUD    

 4002-NS CAMLOC GROMMET            

 214-16ND CAMLOC 4002 Receptacle 



 How do I get the stud into the grommet. Do I have to remove the pin? If so,

 how?



 Cheers

 Peter

 Wonthaggi Australia

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

_________________
Maarten Versteeg
601XL scratch building wings

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum