 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
carlossa52(at)gmail.com
Guest
|
 Posted: Thu Dec 10, 2009 7:02 pm Post subject: stuck |
 |
|
This is embarrassing.
I am stuck. Literally. See pictures - this is an A6 pop rivet. It won't budge, in or out.
Access from the back is rather difficult, as the rear and front rib are already riveted. The A6 is one of the two last rivets in this station.
I can remove the rear rib, but that's my last option - and I still will have a stuck A6 after I remove the rear rib.
Suggestions?
Carlos
CH601-HD, plans
stuck
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
| Description: |
|
| Filesize: |
279.8 KB |
| Viewed: |
4610 Time(s) |
|
| Description: |
|
| Filesize: |
120.51 KB |
| Viewed: |
4610 Time(s) |
|
|
|
| Back to top |
|
 |
lvuman(at)gmail.com
Guest
|
| Posted: Thu Dec 10, 2009 7:48 pm Post subject: stuck |
|
|
I would probably cut it off (dremel tool) then grind it flush. After that, drill it out.
On Thu, Dec 10, 2009 at 8:01 PM, Carlos Sa <carlossa52(at)gmail.com (carlossa52(at)gmail.com)> wrote:
[quote]This is embarrassing.
I am stuck. Literally. See pictures - this is an A6 pop rivet. It won't budge, in or out.
Access from the back is rather difficult, as the rear and front rib are already riveted. The A6 is one of the two last rivets in this station.
I can remove the rear rib, but that's my last option - and I still will have a stuck A6 after I remove the rear rib.
Suggestions?
Carlos
CH601-HD, plans
stuck
[b]
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
|
dougsnash
Joined: 14 Apr 2008
Posts: 281
|
| Posted: Thu Dec 10, 2009 7:52 pm Post subject: stuck |
|
|
Carlos, drill a hole in the flange that is blocking access to the back side of the rivet. The insert a punch through the drilled hole and tap the rivet back out.
Doug MacDonald
CH-701 Scratch Builder
NW Ontario, Canada
Do Not Archive
From: Carlos Sa <carlossa52(at)gmail.com>
To: zenith-list(at)matronics.com; zenith701801-list(at)matronics.com
Sent: Thu, December 10, 2009 9:01:36 PM
Subject: stuck
This is embarrassing.
I am stuck. Literally. See pictures - this is an A6 pop rivet. It won't budge, in or out.
Access from the back is rather difficult, as the rear and front rib are already riveted. The A6 is one of the two last rivets in this station.
I can remove the rear rib, but that's my last option - and I still will have a stuck A6 after I remove the rear rib.
Suggestions?
Carlos
CH601-HD, plans
stuck
Looking for the perfect gift? Give the gift of Flickr! [quote][b]
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
|
bryanekholm
Joined: 16 May 2007
Posts: 25
Location: Minnesota
|
| Posted: Fri Dec 11, 2009 4:14 am Post subject: Re: stuck |
|
|
Try using a little penetrating oil and then either wiggle it out like you were doing or us a punch and rap it out if you can figure out a way to get by the flange on the other side.
Bryan Ekholm
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
_________________
Bryan Ekholm |
|
| Back to top |
|
|
bobkat
Joined: 07 Sep 2008
Posts: 143
Location: Bismarck, ND
|
| Posted: Fri Dec 11, 2009 5:47 am Post subject: stuck |
|
|
I'd cut it flush with a Dremel tool and that little fiber cutting wheel, then drill it out with a pneumatic right angled drill and put in a new one going right through all layers. If you do enlarge the hole a bit by doing this put in a small doubler plate as a washer.
Years ago when I went to build my first airplane another experienced builder told me the number one most important and handy tool to have is a Dremel tool. A couple of airplanes later having worn out 2 or 3 of them I sure agree with him.
[quote] ---
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
|
rvickski(at)yahoo.com
Guest
|
| Posted: Fri Dec 11, 2009 8:11 am Post subject: stuck |
|
|
I'd tap or push the nail in, so the bulge in the nail is through the hole, then grab the body of the rivet with some locking pliers, and wiggle, twist and pull. So what, destroy the rivet, the hole will need re-drilled to accept a new A6, but drilling or hammering from the bulge side with the nail in, expands the rivet, and there is a chance of the drill walking. Save the hole, destroy the rivet.Roy
701 etc.
--- On Thu, 12/10/09, Carlos Sa <carlossa52(at)gmail.com> wrote:
| Quote: |
From: Carlos Sa <carlossa52(at)gmail.com>
Subject: Zenith701801-List: stuck
To: zenith-list(at)matronics.com, zenith701801-list(at)matronics.com
Date: Thursday, December 10, 2009, 10:01 PM
This is embarrassing.
I am stuck. Literally. See pictures - this is an A6 pop rivet. It won't budge, in or out.
Access from the back is rather difficult, as the rear and front rib are already riveted. The A6 is one of the two last rivets in this station.
I can remove the rear rib, but that's my last option - and I still will have a stuck A6 after I remove the rear rib.
Suggestions?
Carlos
CH601-HD, plans
stuck
|
[quote][b]
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
|
n4546v(at)mindspring.com
Guest
|
| Posted: Fri Dec 11, 2009 8:43 am Post subject: stuck |
|
|
do not archive
Just curious Carlos:
Is the hole the correct size for the A6? In the pic it looks undersize.
Regards,
Randy, Las Vegas
[quote] ---
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
|
carlossa52(at)gmail.com
Guest
|
| Posted: Fri Dec 11, 2009 8:50 am Post subject: stuck |
|
|
Yes, it is the right size. I did insert with no great difficulty an A6 in the spar bottom hole.
From the replies I got, I believe A6 fit much more snugly than the A4 and A5.
Carlos
still stuck
2009/12/11 Randy L. Thwing <n4546v(at)mindspring.com (n4546v(at)mindspring.com)>
[quote] do not archive
Just curious Carlos:
Is the hole the correct size for the A6? In the pic it looks undersize.
Regards,
Randy, Las Vegas
[b]
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
