Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

LED Landing lights

Matronics Email Lists Forum Index -> Zenith601-List

View previous topic :: View next topic

Author Message

chris Sinfield

Joined: 28 Nov 2006
Posts: 270
Location: Sydney Australia

Posted: Mon Jan 11, 2010 4:53 am Post subject: LED Landing lights

Hi Gang



Whilst the leading edges are off I was thinking of how much power the 100W Landing and Taxi lights use. 



Has anyone seen a LED replacement globe that would fit in the Standard Zenith Landing /taxi Lights holder? They must use way less power.. My Jab,s Alt puts out 20 Amps total and that would be almost total output in just those 2 items.



Chris.

Geoff Heap

Joined: 12 Jan 2006
Posts: 266
Location: Lindenwold, New Jersey

Posted: Mon Jan 11, 2010 12:30 pm Post subject: Re: LED Landing lights

Know what you mean Chris. The rotax 912 alternator is the same size. I've resolved to live with it until I'm flying. I'll look at it again then....Geoff

paulrod36(at)msn.com
Guest

Posted: Mon Jan 11, 2010 2:55 pm Post subject: LED Landing lights

<?xml:namespace prefix="v" /><?xml:namespace prefix="o" /><![endif]-->  There is a good substitute for incandescents. Mike McKinsey found an LED  light of about 4 inch diameter, (don't know how many LEDs, but a BUNCH) at a  truck stop. Truckers use them for  a worklight at the fifth wheel. I have  no idea what the cost or current draw is, but he has two installed, and they  seem to throw a good beam of light. I'm gonna have to start checking the truck  stops.

  

  

 Paul Rodriguez

 [quote]   ---

LHusky

Joined: 19 Jun 2008
Posts: 86
Location: Madras, Oregon

Posted: Mon Jan 11, 2010 3:52 pm Post subject: LED Landing lights

See if you can get a picture of the installed bulbs.  I would like to  see them installed. 

  

 Larry

  

  In a message dated 1/11/2010 2:56:26 P.M. Pacific Standard Time,  paulrod36(at)msn.com writes:

 [quote]      There is a good substitute for incandescents. Mike McKinsey found an LED    light of about 4 inch diameter, (don't know how many LEDs, but a BUNCH) at a    truck stop. Truckers use them for  a worklight at the fifth wheel. I have    no idea what the cost or current draw is, but he has two installed, and they    seem to throw a good beam of light. I'm gonna have to start checking the truck    stops.

    

    

   Paul Rodriguez

   [quote]     ---

rsteele(at)rjsit.com
Guest

Posted: Mon Jan 11, 2010 4:58 pm Post subject: LED Landing lights

Both the landing lights and the strobes seems like something that  

could be easily made.  LED circuits tend to be really simple.  I've  

searched online and the usual suspect web sites and haven't found  

anything.  I'm wondering if we have any EE's in the group that might  

be able to design something. Those $700 LED strobes look to me like  

something you could build for $50 in parts and a few hours of time.   

Of course if I really knew anything about it, I'd design it myself .



Ron

On Jan 11, 2010, at 3:30 PM, Geoff Heap wrote:



 	  Quote: 	
		   

 <stol10(at)comcast.net>



 Know what you mean Chris. The rotax 912 alternator is the same size.  

 I've resolved to live with it until I'm flying. I'll look at it  

 again then....Geoff





 Read this topic online here:



 http://forums.matronics.com/viewtopic.php?p 81074#281074

paulrod36(at)msn.com
Guest

Posted: Mon Jan 11, 2010 5:04 pm Post subject: LED Landing lights

<?xml:namespace prefix="v" /><?xml:namespace prefix="o" /><![endif]-->  My ability to take a digital picture, get it into the computer, and then  actually append it to an e-mail is roughly the equivalent of a hog reading a  wristwatch. But I've seen his installation, and he has them side by side in a  single window in the left wing, and said he used the mounting piece provided in  the kit.  It looks very professional. If he knows from digital  pitchers and all like that there, I'll ask him to do it.

  

 Paul R.

 [quote]   ---

moorecomp

Joined: 14 Aug 2006
Posts: 32

Posted: Tue Jan 12, 2010 6:36 am Post subject: Re: LED Landing lights

Here are a few links:



Homemade LED light for electric motorcycle:

http://www.instructables.com/id/LED_Motorcycle_Headlight/



Nice selection of LED off road lights:

http://www.responderpse.com/b26-Vision-X-LED-Off-Road-Lights-1.htm



LED strobe kits (could this work on an experimental a/c?):

http://www.responderpse.com/d312-Dual-White-TRI-LED-Hideaway-Kit.htm



Best Regards,

Craig Moore  A&P

Mancelona, MI

agbeyer(at)sbcglobal.net
Guest

Posted: Tue Jan 12, 2010 6:59 am Post subject: LED Landing lights

Hi Chris,

  

 I have an HDS with a Jabiru 3300 that has been flying for five years.  I made my own holder for my Landing/Taxi lights, but I think it is about the same as the "Standard Zenith light holder". I installed standard aircraft Landing/Taxi lights (I think they were 4509's).  I also had Aero flash Nav/Strobes (Double flash) with a tail light in the rudder.  When flying at night I had to manage the use of the lights so I woud not run the battery down.  If I was doing touch & goes and then shut the engine down there might not have been enough power to restart.

  

 I changed to AEROLED's Landing/Taxi lights a couple of years ago. I had the old lights setup like this (One for landing angled down and the other for taxi set level and angled to the right slightly).  I would use one light at a time.  I set the Led's at the same angles but use both at the same time.  They also have a WigWag feature built in.  I use the Landing light switch to power both lights for landing and the Taxi light switch for WigWag.  They don't draw hardly any current and they are brighter.

 

  

I also installed The AEROLED's Nav/Strobe/Tail light combo when they became available.  Even though I now had tail lights in the wings I also installed aan LED tail light in the rudder.  Now I do not have to manage my power consumption  like "The old days". 

  

See attached Pictures. 

  

Regards, 

  

AL from Oshkosh 



    From: chris Sinfield <chris_sinfield(at)yahoo.com.au>

To: zenith601-list(at)matronics.com

Sent: Mon, January 11, 2010 6:53:58 AM

Subject: LED Landing lights



--> Zenith601-List message posted by: "chris Sinfield" <chris_sinfield(at)yahoo.com.au (chris_sinfield(at)yahoo.com.au)>



Hi Gang



Whilst the leading edges are off I was thinking of how much power the 100W Landing and Taxi lights use. 



Has anyone seen a LED replacement globe that would fit in the Standard Zenith Landing /taxi Lights holder? They must use way less power.. My Jab,s Alt puts out 20 Amps total and that would be almost total output in just those 2  items.



Chris.





Read this topic online here:



http://forums.matronics.com/viewtopic.php?p=281000#281000

[b]

IMG_1521.jpg

Description:

Filesize:

56.52 KB

Viewed:

14840 Time(s)

IMG_1584.jpg

Description:

Filesize:

48.93 KB

Viewed:

14840 Time(s)

IMG_1589.jpg

Description:

Filesize:

49.72 KB

Viewed:

14840 Time(s)

Ianrat

Joined: 31 Mar 2008
Posts: 43
Location: Brisbane AUSTRALIA

Posted: Tue Jan 12, 2010 8:05 pm Post subject: Re: LED Landing lights

I have played around with some of the LED,s on the market to try to do what you are asking.

The major problem is that all of the drivers that are readily available put out interference at about 120 meg and this is right were our radios are. All I could get was a lot of noise (I also got some bright lights) but could not use them. I have done the same as Al has done and bitten the bullet and installed the Airoled wing flashers and the landing lights. I was lucky and got mine last year at Oshkosh cheap. 

The only difference is that I have put one light in each wing



Ianrat

CH601XL

Brisbane Australia

backstagelive(at)gmail.co
Guest

Posted: Wed Jan 13, 2010 8:46 am Post subject: LED Landing lights

If you are looking for LED strobes, go to E-bay and type in "LED Strobe". 

You won't believe the selection to choose from! Does anyone know how you can 

make a plastic teardrop lens? What are the regs for strobe placement, 

visibility, etc? This was something I wanted to play with but I'm not that 

far along with the project yet. The one I like the best is Ebay# 

180454805251



Joe in Oshkosh

slook(at)mchsi.com
Guest

Posted: Wed Jan 13, 2010 10:58 am Post subject: LED Landing lights

After looking at vacu-forming and other stuff, I decided I would just 

make a teardrop mold and encapsulate the whole deal including some 

mounting studs in clear Castolite.

That gets you away from making lens and bezels.  It makes for an 

unserviceable unit but it should last practically forever. Haven't 

done this yet but that's the current plan anyway.



Steve



At 10:46 AM 1/13/2010, you wrote:

 	  Quote: 	
		  



Does anyone know how you can make a plastic teardrop lens?


	


Steve Look

Monticello, IL

www.ilrt66.com

"Dogs have owners, Cats have staff"

psm(at)att.net
Guest

Posted: Wed Jan 13, 2010 11:22 am Post subject: LED Landing lights

Hi Steve,



I've been trying to stay out of this line of conversation, but I feel I must

make a comment on your idea of potting the whole light assembly.



If you do that, you might run into serious problems with heat build-up.

While LEDs are very efficient compared to incandescent bulbs, they still are

not 100 percent efficient and will generate heat.  This problem gets worse

since the light outputs you need are incredibly high to meet the FAA

requirements - at least in the case of collision avoidance.  This problem

will be naturally less if you have your light fixture filled with air and

vented rather than a solid structure.



I think you will find vacuum forming of a plastic lens an easy process.  You

just have to heat the plastic enough so it sags and then form it against the

properly shaped mold.  The required temperatures are pretty low - achievable

in a kitchen oven.



Good luck,



Paul

XL awaiting upgrade kit

(retired electrical engineer)

--

tigerrick(at)mindspring.c
Guest

Posted: Wed Jan 13, 2010 11:40 am Post subject: LED Landing lights

Hi, Steve!



I've been following this thread with some interest, as I've been active in the high-intensity LED based position light, strobe, and landing light market in the last few years.



One of the issues with any kind of atmosphere captured inside an LED unit outer lens is the propensity for condensation. If you looked at some of the units mounted on wingtips at the Glasair outdoor display area at OSH this last year, there was a fair amount of water at each end of the lens. And moisture and electronics don't mix too well.



What you're describing, potting the components and circuitry in clear plastic is spot on, and is what Aveo Engineering has been doing from the outset with their units.



You might want to go look at their website before recreating the wheel and doing it yourself. Just a friendly suggestion!



Rick Lindstrom

First Light Aviation Group

Livermore, CA

--

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith601-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum