Matronics Email Lists :: View topic - XL nose wheel fairing fitment

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

XL nose wheel fairing fitment

Matronics Email Lists Forum Index -> Zenith601-List

View previous topic :: View next topic

Author Message

chris Sinfield

Joined: 28 Nov 2006
Posts: 270
Location: Sydney Australia

Posted: Fri Feb 26, 2010 4:32 am Post subject: XL nose wheel fairing fitment

hey I have the 2006 fiberglass nose wheel fairings



I have the photo guides but the WFO-1 plans do not show the size of the sloping Aluminum strip that is riveted to the front portions of the wheel fairing.

Everything else was in the kit but the 2 brackets.. (and they are not on the plans)..



So what size and thickness are they please? and I will make them..

Chris..

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

jaybannist(at)cs.com
Guest

Posted: Fri Feb 26, 2010 5:43 am Post subject: XL nose wheel fairing fitment

Chris,

 

 Is this what you are looking for?

 

 Jay Bannister

 

   

 

  

   

 

   

 

  --

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

scan0001.jpg

Description:

Filesize:

1.17 MB

Viewed:

3361 Time(s)

chris Sinfield

Joined: 28 Nov 2006
Posts: 270
Location: Sydney Australia

Posted: Fri Feb 26, 2010 2:05 pm Post subject: Re: XL nose wheel fairing fitment

thanks Jay

I have the plans page . The Plate I am talking about is where the rear part of the fiberglass fairing, is attached to the fwd part of the nose wheel fairing. It has rivets and anchor nuts on it.



what size and thickness and spacing of the anchor nuts.. 

I cant find it on the plans  I do see it on the photo guide but not its dimensions or thickness or where the holes are located..



Thanks. anyone with it  measure it please

Chris

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

vk3eka(at)bigpond.net.au
Guest

Posted: Fri Feb 26, 2010 2:43 pm Post subject: XL nose wheel fairing fitment

Chris,



I made mine out of some scrap .025 I had lying around. It fits the whole

length of the cut (minus a few mm each end) and is about 50mm wide in total.

I riveted the plate to the front and has nut plates for the rear half.



Next time out at the hangar (tomorrow) I'll take a picture or two.



Cheers



Peter

Wonthaggi Australia



--

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith601-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum