 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
occom
Joined: 26 Aug 2006
Posts: 404
|
 Posted: Sat Mar 13, 2010 5:03 pm Post subject: how to deal with drilled holes. |
 |
|
The three holes in the brace behind the pilots head, and another three on the other side were left when an old advisory changed the fuel system relocating the fuel taps slightly. These have been left as is for a couple hundred hours of flight but I am hot sure that leaving them open is the best idea. I have the idea that sealing or filling them is required/desirable. How or what is the best way to seal these up? Or should I ignore them?
| | - The Matronics Kitfox-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kitfox-List |
|
| Description: |
|
| Filesize: |
40.17 KB |
| Viewed: |
2518 Time(s) |
|
|
|
| Back to top |
|
 |
Lion8
Joined: 21 Jun 2009
Posts: 31
|
| Posted: Sat Mar 13, 2010 6:38 pm Post subject: how to deal with drilled holes. |
|
|
Hello Dave. Any time you have to drill a hole in metal, you weaken a bit. If you should need to fasten somethin to the framework, use the correct clamps. I do understand you may have not drilled them. The metal tube is stronger than common steel and has a bit more corrision resistance. If it were my plane and she was an expermental, I would weld them shut. First I would purge the frame work with Argon or Nitrogen: some inert gas prior to welding.
You should be gettin a few replys after I leave you this one. Good luck.
-Tom
-
| | - The Matronics Kitfox-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kitfox-List |
|
_________________
Tom (Lion8), Currently Flying an LSA Trike
Rebuilding a Kitfox IV Speedster
Southern New Jersey |
|
| Back to top |
|
|
Guy Buchanan
Joined: 16 Jul 2006
Posts: 1204
Location: Ramona, CA
|
| Posted: Sat Mar 13, 2010 10:52 pm Post subject: how to deal with drilled holes. |
|
|
At 05:02 PM 3/13/2010, you wrote:
| Quote: | How or what is the best way to seal these up? Or should I ignore them?
|
In my plane those would be covered by my pipe insulation pad head
rest. I suppose I would put some tape over them too, just to keep
moisture travel to a minimum.
Guy Buchanan
San Diego, CA
K-IV 1200 / 582-C / Warp / 400 hrs. and counting
| | - The Matronics Kitfox-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kitfox-List |
|
_________________
Guy Buchanan
Deceased K-IV 1200
A glider pilot too. |
|
| Back to top |
|
|
Tom Jones
Joined: 12 Mar 2006
Posts: 752
Location: Ellensburg, WA
|
| Posted: Sun Mar 14, 2010 7:28 am Post subject: Re: how to deal with drilled holes. |
|
|
If it was me I would fill them with Hysol, sand and paint.
| | - The Matronics Kitfox-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kitfox-List |
|
_________________
Tom Jones
Classic IV
503 Rotax, 72 inch Two blade Warp
Ellensburg, WA |
|
| Back to top |
|
|
7suds(at)Chartermi.net
Guest
|
| Posted: Sun Mar 14, 2010 10:43 am Post subject: how to deal with drilled holes. |
|
|
I agree with Tom, I would debur the holes, (Burs and sharp edges are
starters for cracks) put in a little linseed Oil and plug with some form of
filler, Hysol, JB Weld, etc. As Tom states at that point you can sand and
paint, and as an added measure of protection make it part of your annual
Inspection too closely inspect the area for signs of cracks.
Lloyd C
Northern Mi.
Mod 5 912 IVO IFA
--
| | - The Matronics Kitfox-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Kitfox-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
