Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Holes left open

Matronics Email Lists Forum Index -> RV10-List

View previous topic :: View next topic

Author Message

rashvac(at)earthlink.net
Guest

Posted: Sun Mar 21, 2010 12:18 pm Post subject: Holes left open

My QB did not have these holes dimpled or countersunk does this cause a problem when finishing?

Can I machine countersink the skins with the longerons riveted?



Russell Shavitz

Shavitz Heating & Air Conditioning

4849 Main Street, Skokie, IL 60077

office:  847-678-1000

cell:  847-417-6622

www.shavitz.com

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

rv10rob(at)gmail.com
Guest

Posted: Sun Mar 21, 2010 8:53 pm Post subject: Holes left open

You definitely want to call Van's (if for nothing else, to notify them of the error).  I don't see how you have much of a choice but to countersink them now.

  

 -Rob

 On Sun, Mar 21, 2010 at 1:15 PM, Russell Shavitz <rashvac(at)earthlink.net (rashvac(at)earthlink.net)> wrote:

  	  Quote: 	
		  --> RV10-List message posted by: Russell Shavitz <rashvac(at)earthlink.net (rashvac(at)earthlink.net)>

 

My QB did not have these holes dimpled or countersunk does this cause a problem when finishing?

Can I machine countersink the skins with the longerons riveted?



Russell Shavitz

Shavitz Heating & Air Conditioning

 4849 Main Street, Skokie, IL 60077

office:  847-678-1000

cell:  847-417-6622

www.sh==================

 Browse, Chat, FAQ,

 ="http://www.matronics.com/Navigator?RV10-List" target="_blank">http://====

  http://forums.mle, List Admin.

 =====



	




 

-- 

Rob Kochman

RV-10 "Finishing" Kit

Woodinville, WA (near Seattle)

http://kochman.net/N819K

  [quote][b]

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

effectus(at)rogers.com
Guest

Posted: Mon Mar 22, 2010 2:19 am Post subject: Holes left open

There is a set of dimple dies that you can get that go in your rivet tool. They work like a pulled rivet.



A pin is put through the center of the back side die and then put through the hole. The front die is put over the pin and then you put the hand rivet pulling tool over the pin.



You then carefully squeeze the two dies together.



This gives you a pretty good dimple that might require s clean up with the counter sink.



Dave Hertner

Sent from my BlackBerry device on the Rogers Wireless Network



--

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

Kelly McMullen

Joined: 16 Apr 2008
Posts: 1188
Location: Sun Lakes AZ

Posted: Mon Mar 22, 2010 5:18 am Post subject: Holes left open

While the pop-rivet dimple die set works well in hard to reach areas,

it is not likely to do much where the layer underneath is a longeron

angle. Had to use the pop-rivet dies on the bottom skin of QB fuse for

the six holes or so on each stiffener at the rear before joining

tailcone.



On Mon, Mar 22, 2010 at 4:10 AM,  <effectus(at)rogers.com> wrote:

 	  Quote: 	
		   There is a set of dimple dies that you can get that go in your rivet tool.

 They work like a pulled rivet.



 A pin is put through the center of the back side die and then put through

 the hole. The front die is put over the pin and then you put the hand rivet

 pulling tool over the pin.



 You then carefully squeeze the two dies together.



 This gives you a pretty good dimple that might require s clean up with the

 counter sink.



 Dave Hertner

 ________________________________

 From: Rob Kochman <rv10rob(at)gmail.com>

 Date: Sun, 21 Mar 2010 21:27:39 -0700

 To: <rv10-list(at)matronics.com>

 Subject: Re: Holes left open

 You definitely want to call Van's (if for nothing else, to notify = them of

 the error).=A0 I don't see how you have much of a choice but to= countersink

 them now.

 =A0

 -Rob



 On Sun, Mar 21, 2010 at 1:15 PM, Russell Shavitz= <rashvac(at)ear= thlink.net>

 wrote:



 --> RV10-List message posted = by: Russell Shavitz <rashvac(at)ea= rthlink.net>



 My QB did not have these holes dimpled or countersunk does this cause a=

 problem when finishing?

 Can I machine countersink the skins with the lo= ngerons riveted?



 Russell Shavitz

 Shavitz Heating & Air Condit= ioning

 4849 Main Street, Skokie, IL 60077

 office: =A0847-678-1000

 cell: =A08= 47-417-6622

 www.sh= =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D

 Browse, Chat, FAQ,

 =3D"http://www.matronics.com/Navigator?RV10-List" target=3D"_blank">http://=

 =3D=3D=3D=3D

 http://forums.m= le, List Admin.

 =3D=3D=3D=3D=3D

 --

 Rob Kochman

 RV-10 "Finishing" Kit=

 Woodinville, WA (near Seattle)

 = http://kochman.net/N819K

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

_________________
Kelly McMullen
A&P/IA, EAA Tech Counselor
KCHD

effectus(at)rogers.com
Guest

Posted: Mon Mar 22, 2010 8:27 am Post subject: Holes left open

Sorry about that! I didn't look closely enough at the location of the problem.



Dave

---

- The Matronics RV10-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV10-List

Display posts from previous:

	Matronics Email Lists Forum Index -> RV10-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum