 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
jcumins(at)jcis.net
Guest
|
 Posted: Thu Jun 03, 2010 9:00 am Post subject: Elevator balance weigth arms |
 |
|
Well I have a slight issue I would like everyone’s opinion on. When final drilling the elevator horns where the push rod connects. I made a filler block according to vans instructions, I did have a thought to make it out of steel or even aluminum block but my desire to keep moving got the best of me and I make it out of oak. We as you can imagine the drill bit walked a bit and the holes did not get drilled as straight as humanly possible as stated in the plans.
I was able to get the balance arms close not not close enough for me to being level with the horiz stab as I would like. I am about 1/16 or a tad more off. When the left side is flush the right side is up about a 1/16 or a tad more. I know this is close and the elevator aft spars are almost perfect parallel to each other when I run a 4 ft level across the back of then to see how close there in line to each other.
So the question is am I being to anal about this or should I g have the left Elevator horn holes welded shut and redrill. Or should I think I am way close enough. I will call vans this morning ro see what they say. I am sure they will say build on.
So if you have not gotten to this step do not use wood make the block out of aluminum or steel.
John G. Cumins
40864 Emp
[quote][b]
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
 |
pitts_pilot(at)bellsouth.
Guest
|
| Posted: Thu Jun 03, 2010 9:11 am Post subject: Elevator balance weigth arms |
|
|
Welcome to the club John. I welded up the offending hole ..... twice ... before I got it right. I made the 'working' block to fill the arm giving much more area to clamp on. I think that I ended up drilling a little dimple to mark the spot and drilling the hole after removing the elevator.
Linn
John Cumins wrote: [quote] Elevator balance weigth arms
Well I have a slight issue I would like everyone’s opinion on. When final drilling the elevator horns where the push rod connects. I made a filler block according to vans instructions, I did have a thought to make it out of steel or even aluminum block but my desire to keep moving got the best of me and I make it out of oak. We as you can imagine the drill bit walked a bit and the holes did not get drilled as straight as humanly possible as stated in the plans.
I was able to get the balance arms close not not close enough for me to being level with the horiz stab as I would like. I am about 1/16 or a tad more off. When the left side is flush the right side is up about a 1/16 or a tad more. I know this is close and the elevator aft spars are almost perfect parallel to each other when I run a 4 ft level across the back of then to see how close there in line to each other.
So the question is am I being to anal about this or should I g have the left Elevator horn holes welded shut and redrill. Or should I think I am way close enough. I will call vans this morning ro see what they say. I am sure they will say build on.
So if you have not gotten to this step do not use wood make the block out of aluminum or steel.
John G. Cumins
40864 Emp
| Quote: |
href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List
href="http://forums.matronics.com">http://forums.matronics.com
href="http://www.matronics.com/contribution">http://www.matronics.com/contribution
|
[b]
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
Strasnuts
Joined: 10 Feb 2009
Posts: 502
Location: Salt Lake City, UT
|
| Posted: Thu Jun 03, 2010 9:25 am Post subject: Re: Elevator balance weigth arms |
|
|
Hi John,
Not sure if you NEED to re-drill but I can guaranty you will think about it for the rest of the build and the first flight (even if it doesn't affect it).
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
_________________
40936
RV-10 SB N801VR Flying
780 Hours
SuperSTOL 60 hours |
|
| Back to top |
|
|
jcumins(at)jcis.net
Guest
|
| Posted: Thu Jun 03, 2010 10:40 am Post subject: Elevator balance weigth arms |
|
|
Linn
Thanks for the reply, were you able to get both elevators flush on both sides or are they off just a tad like mine are.
Having a hard time not knowing they are not perfect hehehe.
John G. Cumins
President
[img]cid:image001.jpg(at)01CB0310.49928410[/img]
2499 B1 Martin Rd
Fairfield Ca 94534
707-425-7100
707-425-7576 Fax
Your Total Technology Solution Provider
From: owner-rv10-list-server(at)matronics.com [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Linn Walters
Sent: Thursday, June 03, 2010 10:10 AM
To: rv10-list(at)matronics.com
Subject: Re: Elevator balance weigth arms
Welcome to the club John. I welded up the offending hole ..... twice .... before I got it right. I made the 'working' block to fill the arm giving much more area to clamp on. I think that I ended up drilling a little dimple to mark the spot and drilling the hole after removing the elevator.
Linn
John Cumins wrote:
Well I have a slight issue I would like everyone’s opinion on. When final drilling the elevator horns where the push rod connects. I made a filler block according to vans instructions, I did have a thought to make it out of steel or even aluminum block but my desire to keep moving got the best of me and I make it out of oak. We as you can imagine the drill bit walked a bit and the holes did not get drilled as straight as humanly possible as stated in the plans.
I was able to get the balance arms close not not close enough for me to being level with the horiz stab as I would like. I am about 1/16 or a tad more off. When the left side is flush the right side is up about a 1/16 or a tad more. I know this is close and the elevator aft spars are almost perfect parallel to each other when I run a 4 ft level across the back of then to see how close there in line to each other.
So the question is am I being to anal about this or should I g have the left Elevator horn holes welded shut and redrill. Or should I think I am way close enough. I will call vans this morning ro see what they say. I am sure they will say build on.
So if you have not gotten to this step do not use wood make the block out of aluminum or steel.
John G. Cumins
40864 Emp | Quote: | | href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List href="http://forums.matronics.com">http://forums.matronics.com href="http://www.matronics.com/contribution">http://www.matronics.com/contribution |
[/b][/quote]http://forums.matronics.com[/url] - List Contribution Web generous nbsp; --> http://www.matronics.com/c=[/b] [/quote]
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
| Description: |
|
| Filesize: |
1.55 KB |
| Viewed: |
4465 Time(s) |
|
|
|
| Back to top |
|
|
pitts_pilot(at)bellsouth.
Guest
|
| Posted: Thu Jun 03, 2010 12:11 pm Post subject: Elevator balance weigth arms |
|
|
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
jesse(at)saintaviation.co
Guest
|
| Posted: Thu Jun 03, 2010 2:34 pm Post subject: Elevator balance weigth arms |
|
|
"I would like everyone's opinion" is a very dangerous statement.
do not archive
Jesse Saint
Saint Aviation, Inc.
jesse(at)saintaviation.com (jesse(at)saintaviation.com)
Cell: 352-427-0285
Fax: 815-377-3694
On Jun 3, 2010, at 12:53 PM, John Cumins wrote:
| Quote: |
Well I have a slight issue I would like everyone’s opinion on. When final drilling the elevator horns where the push rod connects. I made a filler block according to vans instructions, I did have a thought to make it out of steel or even aluminum block but my desire to keep moving got the best of me and I make it out of oak. We as you can imagine the drill bit walked a bit and the holes did not get drilled as straight as humanly possible as stated in the plans.
I was able to get the balance arms close not not close enough for me to being level with the horiz stab as I would like. I am about 1/16 or a tad more off. When the left side is flush the right side is up about a 1/16 or a tad more. I know this is close and the elevator aft spars are almost perfect parallel to each other when I run a 4 ft level across the back of then to see how close there in line to each other.
So the question is am I being to anal about this or should I g have the left Elevator horn holes welded shut and redrill. Or should I think I am way close enough. I will call vans this morning ro see what they say. I am sure they will say build on.
So if you have not gotten to this step do not use wood make the block out of aluminum or steel.
John G. Cumins
40864 Emp
| Quote: |
href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List
href="http://forums.matronics.com/">http://forums.matronics.com
href="http://www.matronics.com/contribution">http://www.matronics.com/contribution
|
|
[quote][b]
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
pitts_pilot(at)bellsouth.
Guest
|
| Posted: Thu Jun 03, 2010 3:02 pm Post subject: Elevator balance weigth arms |
|
|
Jesse, it was a question, not a statement, and where else can you get so many opinions???
Linn
Jesse Saint wrote: [quote]"I would like everyone's opinion" is a very dangerous statement.
do not archive
Jesse Saint
Saint Aviation, Inc.
jesse(at)saintaviation.com (jesse(at)saintaviation.com)
Cell: 352-427-0285
Fax: 815-377-3694
On Jun 3, 2010, at 12:53 PM, John Cumins wrote:
| Quote: |
Well I have a slight issue I would like everyone’s opinion on. When final drilling the elevator horns where the push rod connects. I made a filler block according to vans instructions, I did have a thought to make it out of steel or even aluminum block but my desire to keep moving got the best of me and I make it out of oak. We as you can imagine the drill bit walked a bit and the holes did not get drilled as straight as humanly possible as stated in the plans.
I was able to get the balance arms close not not close enough for me to being level with the horiz stab as I would like. I am about 1/16 or a tad more off. When the left side is flush the right side is up about a 1/16 or a tad more. I know this is close and the elevator aft spars are almost perfect parallel to each other when I run a 4 ft level across the back of then to see how close there in line to each other.
So the question is am I being to anal about this or should I g have the left Elevator horn holes welded shut and redrill. Or should I think I am way close enough. I will call vans this morning ro see what they say. I am sure they will say build on.
So if you have not gotten to this step do not use wood make the block out of aluminum or steel.
John G. Cumins
40864 Emp
href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List
href="http://forums.matronics.com">http://forums.matronics.com
href="http://www.matronics.com/contribution">http://www.matronics.com/contribution
|
[b]
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
Lenny Iszak
Joined: 23 Mar 2008
Posts: 270
|
| Posted: Thu Jun 03, 2010 10:13 pm Post subject: Re: Elevator balance weigth arms |
|
|
I had a similar problem on mine. Van's told me to just weld it and drill it again. I did not want to think about that thing failing while flying, so i just bought new elevator horns and replaced them. Wasn't too hard and I felt that it was worth the effort.
You can see some pictures I posted here:
http://forums.matronics.com/viewtopic.php?t=43969&postdays=0&postorder=asc&start=23
Lenny
#40803
White spaghetti everywhere...
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
jcumins(at)jcis.net
Guest
|
| Posted: Thu Jun 03, 2010 10:22 pm Post subject: Elevator balance weigth arms |
|
|
Jesse
It is like asking what kind of Primer to use or not. HEHEH thanks.
John G. Cumins
President
[img]cid:image001.jpg(at)01CB0372.83B4A440[/img]
2499 B1 Martin Rd
Fairfield Ca 94534
707-425-7100
707-425-7576 Fax
Your Total Technology Solution Provider
From: owner-rv10-list-server(at)matronics.com [mailto:owner-rv10-list-server(at)matronics.com] On Behalf Of Jesse Saint
Sent: Thursday, June 03, 2010 12:57 PM
To: rv10-list(at)matronics.com
Subject: Re: Elevator balance weigth arms
"I would like everyone's opinion" is a very dangerous statement.
do not archive
Jesse Saint
Saint Aviation, Inc.
jesse(at)saintaviation.com (jesse(at)saintaviation.com)
Cell: 352-427-0285
Fax: 815-377-3694
On Jun 3, 2010, at 12:53 PM, John Cumins wrote:
Well I have a slight issue I would like everyone’s opinion on. When final drilling the elevator horns where the push rod connects. I made a filler block according to vans instructions, I did have a thought to make it out of steel or even aluminum block but my desire to keep moving got the best of me and I make it out of oak. We as you can imagine the drill bit walked a bit and the holes did not get drilled as straight as humanly possible as stated in the plans.
I was able to get the balance arms close not not close enough for me to being level with the horiz stab as I would like. I am about 1/16 or a tad more off. When the left side is flush the right side is up about a 1/16 or a tad more. I know this is close and the elevator aft spars are almost perfect parallel to each other when I run a 4 ft level across the back of then to see how close there in line to each other.
So the question is am I being to anal about this or should I g have the left Elevator horn holes welded shut and redrill. Or should I think I am way close enough. I will call vans this morning ro see what they say. I am sure they will say build on.
So if you have not gotten to this step do not use wood make the block out of aluminum or steel.
John G. Cumins
40864 Emp
| Quote: | | href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-Listhref="http://forums.matronics.com/">http://forums.matronics.comhref="http://www.matronics.com/contribution">http://www.matronics.com/contribution |
0123456789 | Quote: | | href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List |
0 | Quote: | | href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List |
1 | Quote: | | href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List |
2 | Quote: | | href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List |
3 | Quote: | | href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List |
4 | Quote: | | href="http://www.matronics.com/Navigator?RV10-List">http://www.matronics.com/Navigator?RV10-List |
5
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
| Description: |
|
| Filesize: |
1.55 KB |
| Viewed: |
4441 Time(s) |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
