Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Horz Relief Angle

Matronics Email Lists Forum Index -> Zenith750-List

View previous topic :: View next topic

Author Message

ifly4fun2(at)sbcglobal.ne
Guest

Posted: Thu Sep 09, 2010 9:48 am Post subject: Horz Relief Angle

Hey all you 750 scratchbuilders,

 For the Horz form block reliefs, what relief angle have you all had sucess with to obtain a semi-flat horz tip rib?  I have 10deg of angle for springback (tried 6deg), should I try 15deg for the reliefs?

  

 Thanks in advance.

  

 do not archive

 ch750 v2

 Art

 [quote][b]

- The Matronics Zenith750-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith750-List

Curt Thompson

Joined: 09 Jan 2009
Posts: 18
Location: Redmond, WA, USA

Posted: Thu Sep 09, 2010 10:04 am Post subject: Horz Relief Angle

Art,  

   

Like you, I started with 6 degrees on my CH701.  I found that 10 degrees worked better.  I still had to tweak the angle a bit after the part came out of the form block.  

   

Curt  

         

  

From: owner-zenith750-list-server(at)matronics.com [mailto:owner-zenith750-list-server(at)matronics.com] On Behalf Of Art Olechowski

 Sent: Thursday, September 09, 2010 10:46 AM

 To: Zenith750

 Subject: Horz Relief Angle  

  

              

Hey all you 750 scratchbuilders,   

      

For the Horz form block reliefs, what   relief angle have you all had sucess with to obtain a semi-flat horz tip   rib?  I have 10deg of angle for springback (tried 6deg), should I   try 15deg for the reliefs?   

      

    

      

Thanks in advance.   

      

    

      

do not archive   

      

ch750 v2   

      

Art   

         	  Quote: 	
		    http://www.matronics.com/Navigator?Zenith750-List 	
0 	  Quote: 	
		   	
1 	  Quote: 	
		   	
2 	  Quote: 	
		   	
3 	  Quote: 	
		   	
4 	  Quote: 	
		   	
5 	  Quote: 	
		   	
6 	  Quote: 	
		   	
7 	  Quote: 	
		   	
8 	  Quote: 	
		   	
9

      [quote][b]

- The Matronics Zenith750-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith750-List

ifly4fun2(at)sbcglobal.ne
Guest

Posted: Thu Sep 09, 2010 5:49 pm Post subject: Horz Relief Angle

Cool Curt thanks for your response. 10 degrees is what I have for springback of the .025 on the flange springback for the horz tip rib but what about the flute reliefs? I surely won'tt want to use the same angle.  I was looking for something that actually works for flute angle for the material thickness.  Be advise I realize this is a as needed purpose relief angle and was thinking 15deg was good.  Just looking for on purpose flute angle .

do not archive

ch750  v2

Art

--- On Thu, 9/9/10, Curt Thompson <charlievictor102(at)hotmail.com> wrote:

 	  Quote: 	
		  

From: Curt Thompson <charlievictor102(at)hotmail.com>

Subject: RE: Zenith750-List: Horz Relief Angle

To: zenith750-list(at)matronics.com

Date: Thursday, September 9, 2010, 1:01 PM



              

Art,   

     

Like you, I started with 6 degrees on my CH701.  I found that 10 degrees worked better.  I still had to tweak the angle a bit after the part came out of the form block.   

     

Curt   

           

  

From: owner-zenith750-list-server(at)matronics.com [mailto:owner-zenith750-list-server(at)matronics.com] On Behalf Of Art Olechowski

 Sent: Thursday, September 09, 2010 10:46 AM

 To: Zenith750

 Subject: Zenith750-List: Horz Relief Angle   

  

                

Hey all you 750 scratchbuilders,    

      

For the Horz form block reliefs, what   relief angle have you all had sucess with to obtain a semi-flat horz tip   rib?  I have 10deg of angle for springback (tried 6deg), should I   try 15deg for the reliefs?    

      

     

      

Thanks in advance.    

      

     

      

do not archive    

      

ch750 v2    

      

Art    

         	  Quote: 	
		      http://www.matronics.com/Navigator?Zenith750-Listhttp://forums.matronics.com  	
0 	  Quote: 	
		    	
1 	  Quote: 	
		    	
2

        	  Quote: 	
		    	
3

	


 [quote][b]

- The Matronics Zenith750-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith750-List

Curt Thompson

Joined: 09 Jan 2009
Posts: 18
Location: Redmond, WA, USA

Posted: Thu Sep 09, 2010 6:38 pm Post subject: Horz Relief Angle

Art,  

   

I used a 1 inch spindle sander to notch for the flutes.  I have a note on one of my wing nose rib form blocks that says I angled them at 45 degrees.  I still used fluting pliers once I got close.  

   

Curt  

         

  

From: owner-zenith750-list-server(at)matronics.com [mailto:owner-zenith750-list-server(at)matronics.com] On Behalf Of Art Olechowski

 Sent: Thursday, September 09, 2010 6:40 PM

 To: zenith750-list(at)matronics.com

 Subject: RE: Horz Relief Angle  

  

                            

Cool Curt thanks for your response. 10 degrees is what I     have for springback of the .025 on the flange springback for the horz tip     rib but what about the flute reliefs? I surely won'tt want to use the same     angle.  I was looking for something that actually works for flute     angle for the material thickness.  Be advise I realize this is a as     needed purpose relief angle and was thinking 15deg was good.  Just     looking for on purpose flute angle .

     

     

     do not archive

     ch750 v2

     Art

     

     

     --- On Thu, 9/9/10, Curt Thompson <charlievictor102(at)hotmail.com>     wrote:     



     From: Curt Thompson <charlievictor102(at)hotmail.com>

     Subject: RE: Horz Relief Angle

     To: zenith750-list(at)matronics.com

     Date: Thursday, September 9, 2010, 1:01 PM               

Art,     

      

Like     you, I started with 6 degrees on my CH701.  I found that 10 degrees     worked better.  I still had to tweak the angle a bit after the part     came out of the form block.     

      

Curt     

                     

     

From:     owner-zenith750-list-server(at)matronics.com [mailto:owner-zenith750-list-server(at)matronics.com]     On Behalf Of Art Olechowski

     Sent: Thursday, September 09,     2010 10:46 AM

     To: Zenith750

     Subject: Horz     Relief Angle     

     

                                 

Hey all you 750       scratchbuilders,       

              

For the Horz       form block reliefs, what relief angle have you all had sucess with       to obtain a semi-flat horz tip rib?  I have 10deg of angle for       springback (tried 6deg), should I try 15deg for the reliefs?       

              

        

              

Thanks in advance.       

              

        

              

do not archive       

              

ch750 v2       

              

Art       

                        	  Quote: 	
		      http://www.matronics.com/Navigator?Zenith750-Listhttp://forums.matronics.comhttp://www.matronics.com/contribution  http://www.matronics.com/contribution

    

    	


               

   

         	  Quote: 	
		      	
0 	  Quote: 	
		    	
1 	  Quote: 	
		    	
2 	  Quote: 	
		    	
3 	  Quote: 	
		    	
4 	  Quote: 	
		    	
5 	  Quote: 	
		    	
6 	  Quote: 	
		    	
7 	  Quote: 	
		    	
8 	  Quote: 	
		    	
9 	  Quote: 	
		  http://www.matronics.com/Navigator?Zenith750-List 	
0 	  Quote: 	
		  http://www.matronics.com/Navigator?Zenith750-List 	
1 	  Quote: 	
		  http://www.matronics.com/Navigator?Zenith750-List 	
2 	  Quote: 	
		  http://www.matronics.com/Navigator?Zenith750-List 	
3 	  Quote: 	
		  http://www.matronics.com/Navigator?Zenith750-List 	
4 	  Quote: 	
		  http://www.matronics.com/Navigator?Zenith750-List 	
5 	  Quote: 	
		  http://www.matronics.com/Navigator?Zenith750-List 	
6

      [quote][b]

- The Matronics Zenith750-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith750-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith750-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum