Matronics Email Lists :: View topic - Gem Sensor Optical Switch wiring

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Gem Sensor Optical Switch wiring

Matronics Email Lists Forum Index -> AeroElectric-List

View previous topic :: View next topic

Author Message

jonlaury

Joined: 06 Nov 2006
Posts: 336

Posted: Sun Sep 26, 2010 1:44 pm Post subject: Gem Sensor Optical Switch wiring

The diagram for wiring this switch to an inductive load (relay coil) doesn't compute for  me. Can someone explain why there's two voltage sources shown? 



The optical switch (40ma) in my fuel line  is being used to drive a pump relay (coil (at) 36ma)



Thanks,

J

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

jonlaury

Joined: 06 Nov 2006
Posts: 336

Posted: Sun Sep 26, 2010 2:13 pm Post subject: Re: Gem Sensor Optical Switch wiring

Forgot the attachment. Here it is.

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

ELS 900 Wiring.pdf

Description:

Download

Filename:

ELS 900 Wiring.pdf

Filesize:

601.24 KB

Downloaded:

485 Time(s)

retasker(at)optonline.net
Guest

Posted: Sun Sep 26, 2010 3:40 pm Post subject: Gem Sensor Optical Switch wiring

I would guess that they show the two sources because one is labeled 5 or 

12 VDC (to power the sensor) and the other is unlabeled.  If you have 

the 12V version of the sensor, just connect the "+" of both supplies 

together.  Basically take the top schematic showing a resistor load and 

substitute the relay and diode from the lower schematic for the resistor 

and you have it.



Dick Tasker



jonlaury wrote:

 	  Quote: 	
		   



 The diagram for wiring this switch to an inductive load (relay coil) doesn't compute for  me. Can someone explain why there's two voltage sources shown?



 The optical switch (40ma) in my fuel line  is being used to drive a pump relay (coil (at) 36ma)



 Thanks,

 J





 Read this topic online here:



 http://forums.matronics.com/viewtopic.php?p=313800#313800



    


	


-- 

Please Note:

No trees were destroyed in the sending of this message.  We do concede, however,

that a significant number of electrons may have been temporarily inconvenienced.

--

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

enginerdy(at)gmail.com
Guest

Posted: Sun Sep 26, 2010 3:47 pm Post subject: Gem Sensor Optical Switch wiring

Hmm. Can I express my dislike for ambiguous datasheets here? Ok, now that that's done..



It may be expressing the fact that the blue wire, the optical receiver, does not care too much what its excitation voltage is. That is, even if you have a 5v or 12v part number, the voltage that drives the blue wire can be a wide range of values as long as it doesn't exceed 40mA if Blue is shorted to ground, as it will be when the sensor is triggered.



The datasheet warns you not to connect the Blue wire to voltage without a limiting load (some sort of resistor, whether it's a relay coil (as in the figure 'Relay Output'), or the pull-up resistor R (as in 'CMOS/TTL Output'), but as long as you do that, you can use either the 5/12v source or some other voltage source.



For your case, it sounds like a configuration like the figure 'External Load' might be the right way to do it, as long as there is a suppression diode in the coil.



This advice isn't authoritative, since I've never worked with a sensor exactly like this before, but just a guess (hopefully a good one) based on experience.



--Daniel



On Sep 26, 2010, at 5:13 PM, jonlaury wrote:



 	  Quote: 	
		   

 

 Forgot the attachment.  Here it is.

 

 

 

 

 Read this topic online here:

 

 http://forums.matronics.com/viewtopic.php?p=313803#313803

 

 

 

 

 Attachments: 

 

 http://forums.matronics.com//files/els_900_wiring_144.pdf

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

jonlaury

Joined: 06 Nov 2006
Posts: 336

Posted: Mon Sep 27, 2010 7:44 am Post subject: Re: Gem Sensor Optical Switch wiring

Dick and Daniel,



Thank you both for the elucidation.



John



Do Not Archive

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

Display posts from previous:

	Matronics Email Lists Forum Index -> AeroElectric-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum