 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
Ianrat
Joined: 31 Mar 2008
Posts: 43
Location: Brisbane AUSTRALIA
|
 Posted: Sun Jan 09, 2011 3:05 am Post subject: OAT Sensor |
 |
|
Where is the best position to install an Out Side Temp Probe on a 601 XL.
Thank you
Ianrat
CH 601 XLB
Brisbane Australia
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
 |
jeffrey_davidson(at)earth
Guest
|
| Posted: Sun Jan 09, 2011 7:04 am Post subject: OAT Sensor |
|
|
Under the saddle in the bulkhead is protected from the direct sun, not
readily visible, and exposed to direct outside air.
Jeff Davidson
--
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
|
jaybannist(at)cs.com
Guest
|
| Posted: Sun Jan 09, 2011 8:10 am Post subject: OAT Sensor |
|
|
Ian,
I mounted my OAT probe inside the right NACA intake fiberglass molding. I figured it would have adequate outside air, not be affected by cowling temps nor the exhaust stream and would be out of the sunlight. It is also a short wiring run from the probe to my Dynon, which has an OAT readout. .
Jay
--
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
| Description: |
|
| Filesize: |
138.74 KB |
| Viewed: |
4492 Time(s) |
|
|
|
| Back to top |
|
|
bryanmmartin
Joined: 10 Jan 2006
Posts: 1018
|
| Posted: Sun Jan 09, 2011 1:33 pm Post subject: OAT Sensor |
|
|
That's where I put mine also.
On Jan 9, 2011, at 11:07 AM, jaybannist(at)cs.com wrote:
| Quote: | Ian,
I mounted my OAT probe inside the right NACA intake fiberglass molding. I figured it would have adequate outside air, not be affected by cowling temps nor the exhaust stream and would be out of the sunlight. It is also a short wiring run from the probe to my Dynon, which has an OAT readout. .
Jay
|
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
_________________
--
Bryan Martin
N61BM, CH 601 XL, Stratus Subaru.
do not archive. |
|
| Back to top |
|
|
Ianrat
Joined: 31 Mar 2008
Posts: 43
Location: Brisbane AUSTRALIA
|
| Posted: Mon Jan 10, 2011 1:49 pm Post subject: Re: OAT Sensor |
|
|
Thank you.
I think I will go with the inlet position. This will keep the wiring short and also out of the way.
Ianrat
CH 601 XLB
Brisbane Australia.
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
