 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
toaster73(at)embarqmail.c
Guest
|
 Posted: Thu Jan 27, 2011 9:04 am Post subject: AHRS Mount angle |
 |
|
I have my AHRS (GRT) mounted behind the baggage bay on the two angles which lay on top of the angle longerons . I see many people have this set up. Best I can tell this does not result in a pitch for the AHRSl which is the same as the door sill (door sill being the level called out for leveling the aircraft). How is this handled ? Do I need to shim it?
Thanks
Chris Lucas
#40072
Approaching painting and other “minor” tidbits
[quote][b]
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
 |
Bob Turner
Joined: 03 Jan 2009
Posts: 885
Location: Castro Valley, CA
|
| Posted: Sat Jan 29, 2011 12:25 pm Post subject: Re: AHRS Mount angle |
|
|
Any real world input? I'd also like to know the answer.
The GRT instructions say to put the AHRS parallel to the longitudinal axis. But there is also a software adjustment to move the vertical bars up/down, "...just as in a conventional AI...". So I don't know how critical this is.
By my measurement (same location, a shelf built off the longitudinal aluminum angles behind the battery) I will need to shim the forward end up by 0.15" for every 7" of length, which is 1.2 degrees. Anyone else get or use these numbers?
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
_________________
Bob Turner
RV-10 QB |
|
| Back to top |
|
|
jesse(at)saintaviation.co
Guest
|
| Posted: Mon Jan 31, 2011 4:50 am Post subject: AHRS Mount angle |
|
|
I didn't see any replies. I haven't done a lot with GRT, but with Dynon and AFS they are quite adamant about getting it as close as you possibly can. In my experience, if it also has a magnetometer in it, it is critical to have it as far away from ferrous metal, especially moving ferrous metal, as possible, but the angle of installation is supposedly very important. I haven't tried installing it other ways, but I'd try to get it as close as possible. If I remember correctly, mounting a 90-degree bracket onto the bulkhead gets it pretty darn close.
do not archive
Jesse Saint
Saint Aviation, Inc.
jesse(at)saintaviation.com
C: 352-427-0285
F: 815-377-3694
On Jan 29, 2011, at 3:25 PM, Bob Turner wrote:
| Quote: |
Any real world input? I'd also like to know the answer.
The GRT instructions say to put the AHRS parallel to the longitudinal axis. But there is also a software adjustment to move the vertical bars up/down, "...just as in a conventional AI...". So I don't know how critical this is.
By my measurement (same location, a shelf built off the longitudinal aluminum angles behind the battery) I will need to shim the forward end up by 0.15" for every 7" of length, which is 1.2 degrees. Anyone else get or use these numbers?
--------
Bob Turner
RV-10 QB
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=328932#328932
|
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
dlm34077(at)q.com
Guest
|
| Posted: Mon Jan 31, 2011 5:39 am Post subject: AHRS Mount angle |
|
|
my backup is a GRT sport with integrated AHRS and external magnetometer.
There is a slight error when mounting the Sport box in the panel but the
pitch adjustment in the software solves that problem. My magnetometer is
mounted on a shelf attached to the longeron in the tailcone. It is off
centerline but parallel to the Crossbow AHRS on the centerline. BTW, the
XBOW is shimmed to match the window sill angle.
---
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
bcondrey
Joined: 03 Apr 2006
Posts: 580
|
| Posted: Mon Jan 31, 2011 7:50 am Post subject: Re: AHRS Mount angle |
|
|
The non-Sport versions of GRT have a separate AHRS and magnetometer to consider. The AHRS must be very close in roll and yaw alignment. While you want it to be close in pitch as well, however there is a pitch offset adjustment in 1 degree increments. If you need to make minor adjustments after your mount is fabricated, shims can be used. Van's sells an AHRS mount that goes behind the baggage bulkhead that guarantees alignment and has attach holes prepunched for several different AHRS units.
The magnetometer also needs to be in alignment, especially with the yaw axis. Typical locations for that are either high in the tailcone or outboard in a wingtip. There's an alignment procedure for the magnetometer that can take out some of the effects from nearby ferrous materials but keep in mind that battery contactors, autopilot servos and trim servos are all little electromagnets that will potentially cause problems. When I installed my magnetometer I found that the level of the longerons was unacceptable because of the battery contactor. I wound up putting it on a small shelf attached to the top J-channels. The center J-channel gives a nice longitudinal reference for alignment.
Bob
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
dlm34077(at)q.com
Guest
|
| Posted: Mon Jan 31, 2011 8:56 am Post subject: AHRS Mount angle |
|
|
Since my install was in 2005 I established the plate on two angles across
the longeron and then ran a fish line from the aft center of the tail cone
to the front center of the tail cone. See before and after pictures
---
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
| Description: |
|
| Filesize: |
889.17 KB |
| Viewed: |
4231 Time(s) |
|
| Description: |
|
| Filesize: |
843.23 KB |
| Viewed: |
4231 Time(s) |
|
| Description: |
|
| Filesize: |
740.08 KB |
| Viewed: |
4231 Time(s) |
|
|
|
| Back to top |
|
|
toaster73(at)embarqmail.c
Guest
|
| Posted: Tue Feb 01, 2011 7:55 pm Post subject: AHRS Mount angle |
|
|
Thanks for the replies, looks like there is somewhat of a consensus to align
with the same plane as the door sill so I will shim under the twin ahrs box
as required. My mount is already a done deal I just wanted to make sure I
should just go ahead and shim it level to the sill.
-Chris
#40072
--
| | - The Matronics RV10-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?RV10-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
