Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

seeping header shutoff valve

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Zenith601-List
View previous topic :: View next topic  
Author Message
larry(at)macsmachine.com
Guest





PostPosted: Fri Apr 15, 2011 9:54 am    Post subject: seeping header shutoff valve Reply with quote

Hi Guys,
This past month an experimental burned up in a t-hangar in Davenport. The suspected reason was a milk house heater setup that was running on and off and that he had a leaking fuel system. The 182 in the adjoining hangar and a boat in the other were both burned. The 182 was written off as totaled. The fuselage exploded and the heat caused the beams above to sag a little. Worst of it all was that he had no insurance. None!
Anyway, I realized my heater system was the same as his and my cockpit had that familiar smell too, so I put my finger around the shutoff fittings and it was damp. It’s the automotive brass cone type with springs that keep it tight for a year or two. This one was the second I’d replaced, so I went to the hardware store and bought a ball valve type with a yellow handle denoting the gas, oil and water compatibility. It took a little while to drain the tank and get the fittings arranged to keep from re-plumbing everything and using a piece of the shutoff without the handle. A slight mod to the valve handle took care of the job.

If you’re using one of these brass fitting, take a look at it! The ball valve types are a much safer bet.
http://www.macsmachine.com/images/controllinkages/full/fuelshutoff2.gif

This week there’s no smell and it’s dry in there.
I’m flying again with great weather and looking forward to more. Endorphins are up again.

Do fly safe,

Larry McFarland at www.macsmachine.com

[quote][b]


- The Matronics Zenith601-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List
Back to top
naumuk(at)windstream.net
Guest





PostPosted: Fri Apr 15, 2011 2:32 pm    Post subject: seeping header shutoff valve Reply with quote

On 04/15/2011 01:49 PM, Larry McFarland wrote:
>
> Hi Guys,
>
> This past month an experimental burned up in a t-hangar in Davenport.
> The suspected reason was a milk house heater setup that was running
> on and off and that he had a leaking fuel system. The 182 in the
> adjoining hangar and a boat in the other were both burned. The 182
> was written off as totaled. The fuselage exploded and the heat
> caused the beams above to sag a little. Worst of it all was that he
> had no insurance. None!
>
> Anyway, I realized my heater system was the same as his and my
> cockpit had that familiar smell too, so I put my finger around the
> shutoff fittings and it was damp. It’s the automotive brass cone
> type with springs that keep it tight for a year or two. This one was
> the second I’d replaced, so I went to the hardware store and bought a
> ball valve type with a yellow handle denoting the gas, oil and water
> compatibility. It took a little while to drain the tank and get the
> fittings arranged to keep from re-plumbing everything and using a
> piece of the shutoff without the handle. A slight mod to the valve
> handle took care of the job.
>
>
>
> If you’re using one of these brass fitting, take a look at it! The
> ball valve types are a much safer bet.
>
> http://www.macsmachine.com/images/controllinkages/full/fuelshutoff2.gif
>
>
>
>
> This week there’s no smell and it’s dry in there.
>
> I’m flying again with great weather and looking forward to more.
> Endorphins are up again.
>
>
>
> Do fly safe,
>
>
>
> Larry McFarland at www.macsmachine.com <http://www.macsmachine.com>
>
>
>
> *
>
> as List
Browse, Chat,
> available via
> generous
> >
> *
Larry-
Please send a picture of the replacement valve.
Bill


[quote][b]


- The Matronics Zenith601-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Zenith601-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group