 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
hletkeman
Joined: 29 Jun 2011
Posts: 8
|
 Posted: Sat Jul 02, 2011 5:43 pm Post subject: DIY Dynon AOA |
 |
|
Hello
I am building a Zenith CH701, and have installed Dynon D180. I am planning to cut the static port so it has a opening from the front, then bend it down at a 45 degree angle, and connect it to my AOA port behind the flightdek. Has anyone tried this, or can anyone comment on this idea.
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
| Description: |
|
| Filesize: |
18.84 KB |
| Viewed: |
9523 Time(s) |
|
|
|
| Back to top |
|
 |
Geoff Heap
Joined: 12 Jan 2006
Posts: 266
Location: Lindenwold, New Jersey
|
| Posted: Wed Jul 06, 2011 7:09 am Post subject: Re: DIY Dynon AOA |
|
|
Hi. I have a D180 also but I purchased the Dynon Pitot/static tube assy with it. In your case, if you put the bend as shown by the black line. Are you then going to cut the tube back so that there is only an inch or so of 45°? Or, instead of the bend as shown, you might put the bend an inch or so from the open end. That would leave the two tube ends closer together. if you make it as shown it looks kinda wild. But hey, why not,if it works.........Geoff
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
_________________
Dual controls. Dynon 180. Icom 210 Garmin 296. Becker transponder. Sigtronics intercom. Electric flaperons. |
|
| Back to top |
|
|
hletkeman
Joined: 29 Jun 2011
Posts: 8
|
| Posted: Thu Oct 06, 2011 12:54 pm Post subject: Re: DIY Dynon AOA |
|
|
a few weeks ago I asked about using the zenith static port as a AOA port. I am now flying the plane, and it seems to work well. I don't have experience with the Dynon AOA probe, so I can tell how it compares. Here is a link to a video clip of the AOA in action
http://www.youtube.com/watch?v=HK0lZnLRahs
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
|
ruruny(at)aol.com
Guest
|
| Posted: Thu Oct 06, 2011 6:57 pm Post subject: DIY Dynon AOA |
|
|
| Quote: | Hey,The setup looks good and like it would work. But I did not see the AOA displayed on your
dynon in the video. Look at the attached picture, in the bottom left corner, its the
red/yellow/green thing. You have to go into the menu to display it. Once displayed, there
is a calibration procedure in the instructions that you have to do while doing power on and off
stalls.Brian a few weeks ago I asked about using the zenith static port as a AOA port. I am
now flying the plane, and it seems to work well. I don't have experience with
the Dynon AOA probe, so I can tell how it compares. Here is a link to a video
clip of the AOA in action
http://www.youtube.com/watch?v=HK0lZnLRahs
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=354216#354216
|
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
| Description: |
|
| Filesize: |
131.82 KB |
| Viewed: |
9326 Time(s) |
|
|
|
| Back to top |
|
|
hletkeman
Joined: 29 Jun 2011
Posts: 8
|
| Posted: Thu Oct 06, 2011 8:15 pm Post subject: Re: DIY Dynon AOA |
|
|
You are right, at the time when I did the video, I had not calibrated the AOA yet. I have done so since, and the bar on the left of the screen is now active. I am thinking about bending the 45degree pipe a bit, and recalibrate, since I have to get rather close to stall before the green line starts to go retract.
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
|
ruruny(at)aol.com
Guest
|
| Posted: Fri Oct 07, 2011 5:37 am Post subject: DIY Dynon AOA |
|
|
I have the dynon pitot tube and the opening for the AOA is alot smaller than the opening for airspeed.
Maybe cap off the end of the AOA with JB weld and drill a very small hole in it.
Brian
[quote][b]
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
