Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Kolb-List Digest: 15 Msgs - 10/11/11

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Kolb-List
View previous topic :: View next topic  
Author Message
GeoB



Joined: 16 Jun 2009
Posts: 207
Location: Fresno, CA

PostPosted: Wed Oct 12, 2011 12:10 am    Post subject: Kolb-List Digest: 15 Msgs - 10/11/11 Reply with quote

Quote:
I get bad interference with the radio from my Jabiru. Obviously need a
suppressor.


Ummm... maybe a suppressor would be the best choice. But maybe not. I have
been into 4x4s. We use radios a lot. And stereos. I have read several VERY
interesting write-ups on successful noise suppression. 4x4 Yahoo groups
might supply some good ideas for you. The basic lesson I learned is that
noise suppression CAN be a a whole mess of things that need attended to. And
maybe not, in your case. I can't recite for you the list of things people
do, but I can give you just a taste...
- try to eliminate noise at the source, not just at the receiving end.
- use the right sort of quality ignition wires, make sure they are installed
properly and are supported properly.
- make sure you understand what you are doing if you install shielding on
your secondary ignition wires. They can work or not work.
- Use by-pass capacitors liberally on power supply lines.
- Ground metal parts, metal sheets, wires, frame sections, etc
- Ground any metal doors. We want to make sure we are not re-radiating a
noise signal.
- be careful of un-terminated or dangling wires that can transmit noise.
- pay special attention to ignition parts; cases and shielding need to be
tight and secure and grounded.
- use by-pass capacitors AT LEAST on the generator. There are other more
complex and expensive noise-elimination items that may be needed here too.
- power supply lines may need a conditioner (your suppressor?). IIRC this
will probably contain capacitance AND reluctance.

At this time of night I can't remember any more off hand.

Please don't believe half of what I wrote- I am trying to recall the flavor
of the suggestions. Personally I would research the issue more closely.


- The Matronics Kolb-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

_________________
GeoB

"Members of Congress should be compelled to wear uniforms like NASCAR drivers, so we could identify their corporate sponsors"
Back to top
View user's profile Send private message
pj.ladd(at)btinternet.com
Guest





PostPosted: Wed Oct 12, 2011 12:40 am    Post subject: Kolb-List Digest: 15 Msgs - 10/11/11 Reply with quote

Thanks George,
that will do to be going on with.

My guru said about the same `you just keep suppressing things until the
noise stops`

Pat


- The Matronics Kolb-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Kolb-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group