 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
skanderup
Joined: 10 Jan 2010
Posts: 11
Location: Denmark
|
 Posted: Sun Feb 12, 2012 2:08 am Post subject: Fitting hinge brackets for flaps on Tri gear |
 |
|
Hello every one,
Once again I would like to draw on your infinite amount of knowledge. My wife and I were yesterday trying to fit the hinges for the flap cross tube.
The two hinge brackets, FL18P and FL18S were laid into the 90mm slots cut in the bottom of the fuselage as per the manual. When threading a thin line between the inner flap hinges it is clear that the FL18 are approximately 12mm too far aft, even though they are hard against the aft bulkhead of the wheel wells. See attached photo.
In order to fit them I am considering two options:
1. Cut about 12mm of the fitting plate part of the FL18 (see attached photo)
2. Make a cut out into the wheel wells to fit the brackets.
Personally I do not find it a good idea to follow no.2, as it will have severe effect on the strength of the main landing gear and the force transfer to the fuselage.
The first option is my preferred one, however I would like to hear other solutions and suggestions.
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
| Description: |
| This is the FL18 and I have marked where I think I will be cutting it, UNLESS I get a better advise. |
|
| Filesize: |
325.97 KB |
| Viewed: |
3051 Time(s) |
|
| Description: |
| FL18S fitted hard up against the wheel well aft bulkhead (still too far aft by approx. 12mm) |
|
| Filesize: |
325.82 KB |
| Viewed: |
3052 Time(s) |
|
|
|
| Back to top |
|
 |
jimpuglise(at)comcast.net
Guest
|
| Posted: Sun Feb 12, 2012 8:01 am Post subject: Fitting hinge brackets for flaps on Tri gear |
|
|
Allan-
As I recall, I had the same problem. I chose to use a Dremel to square the wheel well and slid the bracket slightly forward. I don't think it was nearly as much as 12 mm. Your other option would be to fabricate new FL 18s. As delivered, everything in this airplane "almost fits." During my build, the most common phrase heard was "just make it fit."
Jim Puglise
Europa XS, Jabiru 3300
Punta Gorda, FL
From: "skanderup" <allan_skanderup(at)hotmail.com>
To: europa-list(at)matronics.com
Sent: Sunday, February 12, 2012 5:08:17 AM
Subject: Fitting hinge brackets for flaps on Tri gear
--> Europa-List message posted by: "skanderup" <allan_skanderup(at)hotmail.com>
Hello every one,
Once again I would like to draw on your infinite amount of knowledge. My wife and I were yesterday trying to fit the hinges for the flap cross tube.
The two hinge brackets, FL18P and FL18S were laid into the 90mm slots cut in the bottom of the fuselage as per the manual. When threading a thin line between the inner flap hinges it is clear that the FL18 are approximately 12mm too far aft, even though they are hard against the aft bulkhead of the wheel wells. See attached photo.
In order to fit them I am considering two options:
1. Cut about 12mm of the fitting plate part of the FL18 (see attached photo)
2. Make a cut out into the wheel wells to fit the brackets.
Personally I do not find it a good idea to follow no.2, as it will have severe effect on the strength of the main landing gear and the force transfer to the fuselage.
The first option is my preferred one, however I would like to hear other solutions and suggestions.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=366122#366122
Attachments:
http://forums.matronics.com//files/img00081_20120211_1745_131.jpg
http://forums.matronics.com//files/img00079_20120211_1743_153.jpgbsp; - List Contribution Web Site -
_p; &n====================
[quote][b]
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
|
stephen vestuti
Joined: 05 Jul 2011
Posts: 62
Location: Wales, UK
|
| Posted: Sun Feb 12, 2012 12:10 pm Post subject: Re: Fitting hinge brackets for flaps on Tri gear |
|
|
skanderup,
Did you fit the temorary 12 3/4" spacer between the wheel well and seat back when you bonded the cockpit module in ?
if not, when you load the module with weights for bonding , this gap can be splayed.
I think Nev, Bud or the Factory may be the best people to answer, I think it's easily fixed though,
Steve.
| | - The Matronics Europa-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Europa-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
