Matronics Email Lists :: View topic - Elevator Rib, holes in crimps

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Elevator Rib, holes in crimps

Matronics Email Lists Forum Index -> Zenith701801-List

View previous topic :: View next topic

Author Message

pdelano(at)telus.net
Guest

Posted: Thu Apr 26, 2012 6:03 am Post subject: Elevator Rib, holes in crimps

Hi All,

 

When drilling for the elevator skin along the spar I forgot to mark that there was a crimp in line with the spar and continued to drill right out to the middle of the flange on the Elevator Tip Ribs, 7h1-5. On the top and bottom I have holes on the edge or into this crimp, see attached photos (these were the worst of the 4 holes and are on the bottom). I email Caleb and hope to get an answer from him. Has anyone else done this? If so, did you order new tip ribs or just move away from the crimp and put a new hole respecting edge distance minimums. Is there a minimum distance from a crimp?

 

Regards,

 

Perry

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

ELEVATOR_LR.JPG

Description:

Filesize:

804.29 KB

Viewed:

3230 Time(s)

ELEVATOR_RR.JPG

Description:

Filesize:

863.49 KB

Viewed:

3230 Time(s)

carlossa52(at)gmail.com
Guest

Posted: Thu Apr 26, 2012 7:03 am Post subject: Elevator Rib, holes in crimps

Perry, I suspect you will have to replace the part.

I don't remember whether that happened to me, but if it did, since I am building from plans, I just made another part and threw the old one away.

  You might want to consider making new parts to replace damaged ones, instead of ordering them. For one thing, it's much cheaper, and there are no mail delays...

  



Good luck

  



Carlos

(CH601-HD, plans)



On 26 April 2012 10:01, Perry Delano <pdelano(at)telus.net (pdelano(at)telus.net)> wrote:

  [quote]

Hi All,

   

When drilling for the elevator skin along the spar I forgot to mark that there was a crimp in line with the spar and continued to drill right out to the middle of the flange on the Elevator Tip Ribs, 7h1-5. On the top and bottom I have holes on the edge or into this crimp, see attached photos (these were the worst of the 4 holes and are on the bottom). I email Caleb and hope to get an answer from him. Has anyone else done this? If so, did you order new tip ribs or just move away from the crimp and put a new hole respecting edge distance minimums. Is there a minimum distance from a crimp?  

 

Regards,

 

Perry



[b]

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

Tommy Walker

Joined: 12 Jan 2006
Posts: 442
Location: Anniston, AL 36207

Posted: Thu Apr 26, 2012 7:37 am Post subject: Elevator Rib, holes in crimps

I would remove the crimp and put another crimp just to the side.  I've never heard of edge distance from a crimp.

Tommy Walker

 

On Thu, Apr 26, 2012 at 9:01 AM, Perry Delano <pdelano(at)telus.net (pdelano(at)telus.net)> wrote:

[quote] 

Hi All,

 

When drilling for the elevator skin along the spar I forgot to mark that there was a crimp in line with the spar and continued to drill right out to the middle of the flange on the Elevator Tip Ribs, 7h1-5. On the top and bottom I have holes on the edge or into this crimp, see attached photos (these were the worst of the 4 holes and are on the bottom). I email Caleb and hope to get an answer from him. Has anyone else done this? If so, did you order new tip ribs or just move away from the crimp and put a new hole respecting edge distance minimums. Is there a minimum distance from a crimp? 

 

Regards,

 

Perry



[b]

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

_________________
Tommy Walker
N25A - Anniston, AL

pdelano(at)telus.net
Guest

Posted: Thu Apr 26, 2012 8:04 am Post subject: Elevator Rib, holes in crimps

Hi Tommy I like that idea.Thanks Perry Sent wirelessly from my BlackBerry device on the Bell network.Envoyé sans fil par mon terminal mobile BlackBerry sur le réseau de Bell.

From:  Tommy Walker <twalker(at)cableone.net> 

Sender:  owner-zenith701801-list-server(at)matronics.com 

Date: Thu, 26 Apr 2012 10:35:01 -0500

To: <zenith701801-list(at)matronics.com>

ReplyTo:  zenith701801-list(at)matronics.com

Subject: Re: Zenith701801-List: Elevator Rib, holes in crimps

I would remove the crimp and put another crimp j= ust to the side. =A0I've never heard of edge distance from a crimp.

Tommy Wal= ker

On Thu, Apr 26, 2012 at 9:01 AM, Perry Delan= o <pdelano(at)telus.net (pdelano(at)telus.net)> wrote:

[quote] 

Hi All,

=A0When drilling for the elevator skin along the spar I f= orgot to mark that there was a crimp in line with the spar and continued to=  drill right out to the middle of the flange on the Elevator Tip Ribs, 7h1-= 5. On the top and bottom I have holes on the edge or into this crimp, see a= ttached photos (these were the worst of the 4 holes and are on the bottom).=  I email Caleb and hope to get an answer from him. Has anyone else done thi= s? If so, did you order new tip ribs or just move away from the crimp and p= ut a new hole respecting edge distance minimums. Is there a minimum distanc= e from a crimp? 

=A0

Regards,= 

=A0

Perry

[b]

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

JohnDRead(at)aol.com
Guest

Posted: Thu Apr 26, 2012 8:08 am Post subject: Elevator Rib, holes in crimps

Hi Perry,

                 The  construction standards that you should have on the Zenith disk  that you should have is specific that surfaces MUST contact fully at all  rivet locations or words to that effect. I expect that Caleb will tell you to re  drill the holes that overlap the crimps 10mm away from the offending hole. Caleb  may have a good solution as to how to fill the offending holes too

  

 Regards,  John



CH701 - Colorado - Jabiru 3300



Cell: 719-494-4567

Home:  303-648-3261   

  In a message dated 4/26/2012 8:29:56 A.M. Mountain Daylight Time,  pdelano(at)telus.net writes:

  	  Quote: 	
		        

Hi All,   

    

When drilling for the elevator skin along the spar I forgot    to mark that there was a crimp in line with the spar and continued to drill    right out to the middle of the flange on the Elevator Tip Ribs, 7h1-5. On the    top and bottom I have holes on the edge or into this crimp, see attached    photos (these were the worst of the 4 holes and are on the bottom). I email    Caleb and hope to get an answer from him. Has anyone else done this? If so,    did you order new tip ribs or just move away from the crimp and put a new hole    respecting edge distance minimums. Is there a minimum distance from a    crimp?   

    

Regards,   

    

Perry

	




 [quote][b]

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

JohnDRead(at)aol.com
Guest

Posted: Thu Apr 26, 2012 8:44 am Post subject: Elevator Rib, holes in crimps

Good solution, just make sure that the mating surface contact fully.

  

 Regards,  John



CH701 - Colorado - Jabiru 3300



Cell: 719-494-4567

Home:  303-648-3261   

  In a message dated 4/26/2012 10:40:14 A.M. Mountain Daylight Time,  twalker(at)cableone.net writes:

  	  Quote: 	
		     I would remove the crimp and put another crimp just to    the side.  I've never heard of edge distance from a crimp.

   



   Tommy Walker



   On Thu, Apr 26, 2012 at 9:01 AM, Perry Delano <pdelano(at)telus.net (pdelano(at)telus.net)> wrote:

    	  Quote: 	
		                 

Hi All,     

      

When drilling for the elevator skin along the spar I      forgot to mark that there was a crimp in line with the spar and continued to      drill right out to the middle of the flange on the Elevator Tip Ribs, 7h1-5.      On the top and bottom I have holes on the edge or into this crimp, see      attached photos (these were the worst of the 4 holes and are on the bottom).      I email Caleb and hope to get an answer from him. Has anyone else done this?      If so, did you order new tip ribs or just move away from the crimp and put a      new hole respecting edge distance minimums. Is there a minimum distance from      a crimp?     

      

Regards,     

      

Perry







ist href="http://www.matronics.com/Navigator?Zenith701801-List">http://www.matronics.com/Navigator?Zenith701801-List

s.matronics.com/">http://forums.matronics.com

p://www.matronics.com/contribution">http://www.matronics.com/contribution



	
	




 [quote][b]

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

pdelano(at)telus.net
Guest

Posted: Thu Apr 26, 2012 11:10 am Post subject: Elevator Rib, holes in crimps

Hi Tommy,   



Caleb suggested the same idea. Just shift the crimp. 



Perry  





Sent wirelessly from my BlackBerry device on the Bell network.

Envoyé sans fil par mon terminal mobile BlackBerry sur le réseau de Bell.



--

- The Matronics Zenith701801-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith701801-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith701801-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum