Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

bushings

Matronics Email Lists Forum Index -> Zenith601-List

View previous topic :: View next topic

Author Message

carlossa52(at)gmail.com
Guest

Posted: Mon Jun 11, 2012 8:13 am Post subject: bushings

Hello,Some time ago - but I think this year - somebody posted some information about bushings.  I spent a long while searching, but couldn't find neither the post nor the product.Does anybody remember it?  ...and while I have your attention: the upper and lower rudder hinges have different size holes (1/4" and 3/16" respectively), but the bushing is 1/4" for both...??  ThanksCarlos

   [quote][b]

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

jaybannist(at)cs.com
Guest

Posted: Mon Jun 11, 2012 8:34 am Post subject: bushings

Carlos,

 

 The "fork" parts of the hinges have a 3/16" hole, for a AN3 bolt.  The "tongue" parts of the hinges have a 1/4" hole for the 1/4" bushing.  The bolt clamps the bushing between the "fork" parts to make a fixed "hole" for the "tongue" part to rotate around.  Drawing 6-S-5 for the 501XL shows this very clearly.

 

 Jay

    

  

     

  

     

  

    --

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

JohnDRead(at)aol.com
Guest

Posted: Mon Jun 11, 2012 8:37 am Post subject: bushings

Hi Carlos,

             Attached  are the changes I made to the rudder bearings on my 701.

  

 Regards,  John



CH701 - Colorado - Jabiru 3300



Cell: 719-494-4567

Home:  303-648-3261   

  In a message dated 6/11/2012 10:14:14 A.M. Mountain Daylight Time,  carlossa52(at)gmail.com writes:

  	  Quote: 	
		  Hello,Some time ago -    but I think this year - somebody posted some information about    bushings.I spent a long while searching, but couldn't find    neither the post nor the product.Does anybody    remember it?...and while I    have your attention: the upper and lower rudder hinges have different size    holes (1/4" and 3/16" respectively), but the bushing is 1/4" for    both...??ThanksCarlos

 	  Quote: 	
		  



 href="http://www.matronics.com/Navigator?Zenith601-List">http://www.matronics.com/Navigator?Zenith601-List

s.matronics.com/">http://forums.matronics.com

p://www.matronics.com/contribution">http://www.matronics.com/contribution

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

carlossa52(at)gmail.com
Guest

Posted: Mon Jun 11, 2012 9:02 am Post subject: bushings

John, thanks much for this!I might go this way - but this is not what I was looking for...   I think the bushing this gentleman was talking about was something involving bronze and teflon...

  CheersCarlos

 

 On 11 June 2012 12:36,  <JohnDRead(at)aol.com (JohnDRead(at)aol.com)> wrote:

[quote]       Hi Carlos,

             Attached  are the changes I made to the rudder bearings on my 701.

  

 Regards,  John



CH701 - Colorado - Jabiru 3300



Cell: 719-494-4567

Home:  303-648-3261   

  In a message dated 6/11/2012 10:14:14 A.M. Mountain Daylight Time,  carlossa52(at)gmail.com (carlossa52(at)gmail.com) writes:

  	  Quote: 	
		  Hello,  Some time ago -    but I think this year - somebody posted some information about    bushings.I spent a long while searching, but couldn't find    neither the post nor the product.Does anybody    remember it?...and while I    have your attention: the upper and lower rudder hinges have different size    holes (1/4" and 3/16" respectively), but the bushing is 1/4" for    both...??ThanksCarlos

   	  Quote: 	
		  



 href="http://www.matronics.com/Navigator?Zenith601-List">http://www.matronics.com/Navigator?Zenith601-List

s.matronics.com/">http://forums.matronics.com

p://www.matronics.com/contribution">http://www.matronics.com/contribution



	
	


[b]

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

Jon(at)joncroke.com
Guest

Posted: Mon Jun 11, 2012 9:32 am Post subject: bushings

I think Larry Zepp had an article on bushings in the last Zenair Newsletter.

From: owner-zenith601-list-server(at)matronics.com [mailto:owner-zenith601-list-server(at)matronics.com] On Behalf Of Carlos Sa

Sent: Monday, June 11, 2012 1:01 PM

To: zenith601-list(at)matronics.com

Subject: Re: bushings

John, thanks much for this!

I might go this way - but this is not what I was looking for...   I think the bushing this gentleman was talking about was something involving bronze and teflon...

 	  Quote: 	

  [quote][b]

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

carlossa52(at)gmail.com
Guest

Posted: Mon Jun 11, 2012 9:43 am Post subject: bushings

BINGO ! ! !mscdirect.com , PN 00458430 and 00458455  thanks a bunch, JonCarlos

  On 11 June 2012 13:30, Jon Croke <Jon(at)joncroke.com (Jon(at)joncroke.com)> wrote:

[quote]  

I think Larry Zepp had an article on bushings in the last Zenair Newsletter.  

 

From: owner-zenith601-list-server(at)matronics.com (owner-zenith601-list-server(at)matronics.com) [mailto:owner-zenith601-list-server(at)matronics.com (owner-zenith601-list-server(at)matronics.com)] On Behalf Of Carlos Sa

  Sent: Monday, June 11, 2012 1:01 PM

To: zenith601-list(at)matronics.com (zenith601-list(at)matronics.com)

Subject: Re: bushings  

 

John, thanks much for this!



I might go this way - but this is not what I was looking for...   I think the bushing this gentleman was talking about was something involving bronze and teflon...

  



 	  Quote: 	
		   



" target="_blank">http://www.matronics.com/Navigator?Zenith601-List

tp://forums.matronics.com

_blank">http://www.matronics.com/contribution



	


[b]

- The Matronics Zenith601-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith601-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith601-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum