 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
carlossa52(at)gmail.com
Guest
|
 Posted: Sun Jul 08, 2012 4:00 pm Post subject: CH601-HD(S) fuselage assembly |
 |
|
Hello, folksMy aluminum stack is finally starting to resemble an aircraft (if you have a lot of imagination, that is): http://www.zenith.aero/photo/img-6058When I put the front side skins in place (just to have an idea of what it would look like), I noticed the interference between the side skins, heel support and floor (the rolled end of the floor). The attached pics show the offending area.The instructions simply say "trim as required" (or something like that). To me, it seems I'll have to remove a semi-circle one or two inches in diameter - as I haven't seen any comments about this, I am a little concerned. I also have looked at a few of the CH601 sites still on-line, but I did not find any picture or comment that would clarify this. Thanks in advance for your comments / suggestions CarlosCH601-HD, plans
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
| Description: |
|
| Filesize: |
1.92 MB |
| Viewed: |
2974 Time(s) |
|
| Description: |
|
| Filesize: |
1.75 MB |
| Viewed: |
2974 Time(s) |
|
|
|
| Back to top |
|
 |
jaybannist(at)cs.com
Guest
|
| Posted: Sun Jul 08, 2012 5:32 pm Post subject: CH601-HD(S) fuselage assembly |
|
|
Carlos,
I'm not sure when it started, but I discovered this problem (with my 601XL) in June 2006 and reported it to Zenith. They published a revised photo guide page, saying that it had to be trimmed. (I had already done that) I think they revised the part after that, but I really don't know if they ever revised the drawing for the part.
Jay
--
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
|
carlossa52(at)gmail.com
Guest
|
| Posted: Sun Jul 08, 2012 5:40 pm Post subject: CH601-HD(S) fuselage assembly |
|
|
So it happens on the XL as well?! I'll take a look at XL pics, then Thanks, JayCarlos
On 8 July 2012 21:31, Jay Bannister <jaybannist(at)cs.com (jaybannist(at)cs.com)> wrote:
[quote] Carlos,
I'm not sure when it started, but I discovered this problem (with my 601XL) in June 2006 and reported it to Zenith. They published a revised photo guide page, saying that it had to be trimmed. (I had already done that) I think they revised the part after that, but I really don't know if they ever revised the drawing for the part.
Jay
--
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
|
bryanmmartin
Joined: 10 Jan 2006
Posts: 1018
|
| Posted: Mon Jul 09, 2012 3:43 am Post subject: CH601-HD(S) fuselage assembly |
|
|
I would trim the corner of the heel support, it's non structural. Trim the side skin only if necessary.
On Jul 8, 2012, at 6:58 PM, Carlos Sa wrote:
| Quote: | When I put the front side skins in place (just to have an idea of what it would look like), I noticed the interference between the side skins, heel support and floor (the rolled end of the floor).
The attached pics show the offending area.
The instructions simply say "trim as required" (or something like that).
To me, it seems I'll have to remove a semi-circle one or two inches in diameter - as I haven't seen any comments about this, I am a little concerned.
I also have looked at a few of the CH601 sites still on-line, but I did not find any picture or comment that would clarify this.
|
--
Bryan Martin
N61BM, CH 601 XL,
RAM Subaru, Stratus re-drive.
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
_________________
--
Bryan Martin
N61BM, CH 601 XL, Stratus Subaru.
do not archive. |
|
| Back to top |
|
|
carlossa52(at)gmail.com
Guest
|
| Posted: Mon Jul 09, 2012 4:38 am Post subject: CH601-HD(S) fuselage assembly |
|
|
Thanks for the input, Brian
On 9 July 2012 07:42, Bryan Martin <bryanmmartin(at)comcast.net (bryanmmartin(at)comcast.net)> wrote:
[quote]--> Zenith601-List message posted by: Bryan Martin <bryanmmartin(at)comcast.net (bryanmmartin(at)comcast.net)>
I would trim the corner of the heel support, it's non structural. Trim the side skin only if necessary.
On Jul 8, 2012, at 6:58 PM, Carlos Sa wrote:
> When I put the front side skins in place (just to have an idea of what it would look like), I noticed the interference between the side skins, heel support and floor (the rolled end of the floor).
> The attached pics show the offending area.
> The instructions simply say "trim as required" (or something like that).
> To me, it seems I'll have to remove a semi-circle one or two inches in diameter - as I haven't seen any comments about this, I am a little concerned.
> I also have looked at a few of the CH601 sites still on-line, but I did not find any picture or comment that would clarify this.
--
Bryan Martin
N61BM, CH 601 XL,
RAM Subaru, Stratus re-drive.[b]
| | - The Matronics Zenith601-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith601-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
