Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

GSC propeller

Matronics Email Lists Forum Index -> Kolb-List

View previous topic :: View next topic

Author Message

pipercolt

Joined: 08 Jan 2012
Posts: 46
Location: Randolph New York

Posted: Thu Sep 13, 2012 6:13 pm Post subject: GSC propeller

I have a Kolb Mk 111 with a Rotax 582. Has anyone had any experience with GSC propellers?

Thanks

Bob

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

John Hauck

Joined: 09 Jan 2006
Posts: 4639
Location: Titus, Alabama (hauck's holler)

Posted: Thu Sep 13, 2012 7:58 pm Post subject: GSC propeller

<bob.pipercolt(at)yahoo.com>



I have a Kolb Mk 111 with a Rotax 582. Has anyone had any

experience with GSC propellers?

Thanks

Bob

  

Had a 3 blade GSC prop fail, Sep 1993.  Collected all 3

blades on the tail boom.  Had to replace the tail boom.



Immediately started flying Warp Drive props, and have for

more than 3,000 WD since then, on 582, 912UL and 912ULS.



Attached are photos of GSC and Warp Drive Blade Grips.  No

comparison between the two.



john h

mkIII

Rock House, OR

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

GSC_Blade_Grip.jpg

Description:

Filesize:

36.74 KB

Viewed:

6657 Time(s)

WarpDrive_blade_butt.JPG

Description:

Filesize:

36.77 KB

Viewed:

6657 Time(s)

_________________
John Hauck
MKIII/912ULS
hauck's holler
Titus, Alabama

brubakermal(at)yahoo.com
Guest

Posted: Thu Sep 13, 2012 8:46 pm Post subject: GSC propeller

I had one on my plane, the people in the shop are great to talk  to, easy to get along with and understand.  Give them a call thell set you up. I like the look of wood and becouse it is wood alot of people seem to replace them  as soon as they buy a plane that has one so, used ones are easy to find and cheep But still worth the money.

 Thanks To the people who responded to  my firestar request were still looking but got a couple leads.  Please call if you would consider selling your firestar.  mal



 

Malcolm & Jeanne Brubaker  

Michigan Sport Pilot Repair 

 http://michigansportpilotrepair.com/

 LSRM-A, PPC, WS

Great Sails - Sailmaker 

for Ultralight & Light Sport

(989)513-3022

  

  

  

  

      

  From: pipercolt <bob.pipercolt(at)yahoo.com>

 To: kolb-list(at)matronics.com 

 Sent: Thursday, September 13, 2012 10:13 PM

 Subject: GSC propeller

  

 

--> Kolb-List message posted by: "pipercolt" <bob.pipercolt(at)yahoo.com (bob.pipercolt(at)yahoo.com)>



I have a Kolb Mk 111 with a Rotax 582. Has anyone had any experience with GSC propellers?

Thanks

Bob





Read this topic online here:



http://forums.matronics.com/viewtopic.ptronics.com/Navigator?Kolb-List" ="http://forums.matronics.com/" target="_blank">http://forums.matronics                    &nbsptronics.com/contribution" target="_blank">http://www.matronics.com/contri================



 

 

   

 [quote][b]

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

Dana

Joined: 13 Dec 2007
Posts: 1047
Location: Connecticut, USA

Posted: Fri Sep 14, 2012 2:39 am Post subject: GSC propeller

At 11:56 PM 9/13/2012, John Hauck wrote:



  	  Quote: 	
		  Had a 3 blade GSC prop fail, Sep 1993.  Collected all 3

 blades on the tail boom.  Had to replace the tail boom. 	


 John, I assume that was on the ground?



 Dana

 --

 There are 3 kinds of people: those who can count & those who can't.    

    [quote][b]

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

Dana

Joined: 13 Dec 2007
Posts: 1047
Location: Connecticut, USA

Posted: Fri Sep 14, 2012 2:39 am Post subject: GSC propeller

At 10:13 PM 9/13/2012, pipercolt wrote:

  	  Quote: 	
		  --> Kolb-List message posted by: "pipercolt" <bob.pipercolt(at)yahoo.com>



 I have a Kolb Mk 111 with a Rotax 582. Has anyone had any experience with GSC propellers?

 Thanks 	


 Had one on a PPG and was very happy with it.



 Dana

 --

 There are 3 kinds of people: those who can count & those who can't.    

    [quote][b]

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

John Hauck

Joined: 09 Jan 2006
Posts: 4639
Location: Titus, Alabama (hauck's holler)

Posted: Fri Sep 14, 2012 6:25 am Post subject: GSC propeller

Had a 3 blade GSC prop fail, Sep 1993.  Collected all 3

blades on the tail boom.  Had to replace the tail boom.



John, I assume that was on the ground?



Dana

 

Was climbing full throttle.  Probably had the dual K&N air

filter go through the GSC, but cannot say for certain.

Never found it.  If I had had the filter safety wired, I

would know for sure it did not go through the prop.



The 582 immediately shut down as the carbs were thrown from

the sockets, and the starter was ejected from the mag end of

the engine.  Carbs and starter were captured by the cables.



Made a forced landing in the smallest "shoe box" sized field

I have ever landed in without putting a scratch on the

MKIII.



john h

mkIII

Rock House, OR

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

_________________
John Hauck
MKIII/912ULS
hauck's holler
Titus, Alabama

Dana

Joined: 13 Dec 2007
Posts: 1047
Location: Connecticut, USA

Posted: Fri Sep 14, 2012 9:18 am Post subject: GSC propeller

So what did it do to the tail boom that you were able to land it, but had to replace it?  Makes me feel a bit better about the tailboom's safety factor...



 -Dana



 At 10:22 AM 9/14/2012, John Hauck wrote:

 [quote]--> Kolb-List message posted by: "John Hauck" <jhauck(at)elmore.rr.com>



 Was climbing full throttle.  Probably had the dual K&N air

 filter go through the GSC, but cannot say for certain.

 Never found it.  If I had had the filter safety wired, I

 would know for sure it did not go through the prop.



 The 582 immediately shut down as the carbs were thrown from

 the sockets, and the starter was ejected from the mag end of

 the engine.  Carbs and starter were captured by the  cables.



 Made a forced landing in the smallest "shoe box" sized field

 I have ever landed in without putting a scratch on the

 MKIII.



 john h

 mkIII

 Rock House, OR



 



 

 Email Forum -

 http://www.matronics.com/Navigator?Kolb-List

 - MATRONICS WEB FORUMS -

 http://forums.matronics.com

 - List Contribution Web Site -

 -Matt Dralle, List Admin.

 http://www.matronics.com/contribution

 --

 Knowledge is knowing a tomato is a fruit. Wisdom is not putting it in a fruit salad.

    [quote][b]

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

John Hauck

Joined: 09 Jan 2006
Posts: 4639
Location: Titus, Alabama (hauck's holler)

Posted: Fri Sep 14, 2012 11:48 am Post subject: GSC propeller

So what did it do to the tail boom that you were able to

land it, but had to replace it?  Makes me feel a bit better

about the tailboom's safety factor...



-Dana

   

As you can imagine, there was a pretty good size dimple in

the side of the boom tube in the area of the H brace.  The

tail boom was struck hard enough to knock it about 5 degrees

out of column.  I had no idea that the tail boom was bent

until after the forced landing.  In fact, all I knew was

there was a terrific explosion, followed by severe vibration

momentarily, then severe quiet.  I had a small rectangular

field surrounded on two sides by high tension power wires,

one side by a large bamboo thicket and the other side by

tall trees.



The tail boom is tough, both 5 and 6 inch boom tubes.  They

are also very flexible which prolongs their life in the

severe environment that they live.



Scratches and nicks in the surface of the tube would be

cause for concern.  However, I know of one boom tube, 5",

that got nicked and dimpled from FOD.  The owner/pilot used

scotch bright wheels to buff and polish out the surface.

Flew many hours, then sold the aircraft to a really big

pilot.  The FSII continues to fly safely.



john h

mkIII

Rock House, OR

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

_________________
John Hauck
MKIII/912ULS
hauck's holler
Titus, Alabama

gajindra(at)sbcglobal.net
Guest

Posted: Fri Sep 14, 2012 3:03 pm Post subject: GSC propeller

Had a GSC on my 582 till an axle bolt broke on landing and went thru the prop.Split one blade from tip to root.Replaced with an IVO.Love the IVO.But I also liked the GSC till it broke.Replaced the AN 3 axle bolts with AN 4 bolts

 

  Gary Jindra

 Mark 3c

 99 hours



 



 

   From: pipercolt <bob.pipercolt(at)yahoo.com>

To: kolb-list(at)matronics.com

Sent: Thu, September 13, 2012 10:13:13 PM

Subject: GSC propeller



--> Kolb-List message posted by: "pipercolt" <bob.pipercolt(at)yahoo.com (bob.pipercolt(at)yahoo.com)>



I have a Kolb Mk 111 with a Rotax 582. Has anyone had any experience with GSC propellers?

Thanks

Bob





Read this topic online here:



http://forums.matronics.com/viewtopic.php?p=383023#383023

 Matronics List Features Navigator to /www.matronics.com/Navigator?Kolb-List" target=_blank>http://www.matronicsp;             -Matt Dralle, List Admin.



 [quote][b]

- The Matronics Kolb-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Kolb-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Kolb-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum