 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
pdelano(at)telus.net
Guest
|
 Posted: Fri Nov 30, 2012 7:44 am Post subject: 7V4-5 Slat Support Positioning Template |
 |
|
I cannot find a dimension for the top hole on this jig, the bottom hole: X= 70, Y= 68 however the Top hole is X=35, Y = unknown. By default the top finds its own position but it would be nice to have the vertical dimension or an angle for the slat support to check. The template is shown on dwg. 7-V-5.
Any direction is appreciated.
[quote][b]
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
 |
bobmccully
Joined: 25 Nov 2012
Posts: 2
Location: Red Deer, Alberta, Canada
|
| Posted: Fri Nov 30, 2012 5:17 pm Post subject: Re: 7V4-5 Slat Support Positioning Template |
|
|
Hello
Look at page 7V4 and again at 7V4-5 Slat Supports. Shows both holes 8mm in from edge, 55 mm apart with one hole 13 mm from one corner. Think that is what you are asking?
Bob
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
_________________
not sure what this is? |
|
| Back to top |
|
|
dan(at)hillsgun.com
Guest
|
| Posted: Fri Nov 30, 2012 6:41 pm Post subject: 7V4-5 Slat Support Positioning Template |
|
|
As per the note above the template drawing. Mark a line vertical line at the 35 dimension, cleco the bottom hole, rotate the slat support until the top hole intersects the 35mm line and it is positioned correctly. Hope this helps. Dan.
From: owner-zenith701801-list-server(at)matronics.com [mailto:owner-zenith701801-list-server(at)matronics.com] On Behalf Of Perry Delano
Sent: Friday, November 30, 2012 7:43 AM
To: zenith701801-list(at)matronics.com
Subject: 7V4-5 Slat Support Positioning Template
I cannot find a dimension for the top hole on this jig, the bottom hole: X= 70, Y= 68 however the Top hole is X=35, Y = unknown. By default the top finds its own position but it would be nice to have the vertical dimension or an angle for the slat support to check. The template is shown on dwg. 7-V-5.
Any direction is appreciated.
012345678901234567
[quote][b]
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
|
pdelano(at)telus.net
Guest
|
| Posted: Fri Nov 30, 2012 7:25 pm Post subject: 7V4-5 Slat Support Positioning Template |
|
|
Thanks Dan, Got to check those dwg updates next time. Working with 2003 R2 dwg and had not looked at updates where the addition of the note appears. Your post helped me clue in that I was missing something on my plans, I'll print them off an put them with the plans now. Sent wirelessly from my BlackBerry device on the Bell network.Envoyé sans fil par mon terminal mobile BlackBerry sur le réseau de Bell.
From: "Dan Hill" <dan(at)hillsgun.com>
Sender: owner-zenith701801-list-server(at)matronics.com
Date: Fri, 30 Nov 2012 18:41:19 -0800
To: <zenith701801-list(at)matronics.com>
ReplyTo: zenith701801-list(at)matronics.com
Subject: RE: Zenith701801-List: 7V4-5 Slat Support Positioning Template
As per the note above the template drawing. Mark = a line vertical line at the 35 dimension, cleco the bottom hole, rotate = the slat support until the top hole intersects the 35mm line and it is = positioned correctly. Hope this helps. Dan.
From:= = owner-zenith701801-list-server(at)matronics.com = [mailto:owner-zenith701801-list-server(at)matronics.com] On Behalf Of = Perry Delano
Sent: Friday, November 30, 2012 7:43 = AM
To: zenith701801-list(at)matronics.com
Subject: = Zenith701801-List: 7V4-5 Slat Support Positioning = Template
I cannot = find a dimension for the top hole on this jig, the bottom hole: X=3D 70, = Y=3D 68 however the Top hole is X=3D35, Y =3D unknown. By = default the top finds its own position but it would be nice to have the = vertical dimension or an angle for the slat support to check. The = template is shown on dwg. 7-V-5.
Any = direction is appreciated.
0123456789012= 34567
[quote][b]
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
