Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Cowl Hinge Pins

Matronics Email Lists Forum Index -> RV10-List

View previous topic :: View next topic

Author Message

schmoboy

Joined: 26 Feb 2006
Posts: 130

Posted: Sat Dec 15, 2012 8:32 am Post subject: Cowl Hinge Pins

Anyone know a source for the stainless hinge pins besides Vans?  I don't 

understand why they don't provide enough for the side hinges between the 

top and bottom cowl.  Page 47-8 says they are available from the 

accessories catalog.  I'd think they are more than just accessories.  I 

understand that they weld on a retainer for these "accessories", but one 

would think that it would be supplied in the kit.



-Sean #40303

carl.froehlich(at)verizon
Guest

Posted: Sat Dec 15, 2012 1:40 pm Post subject: Cowl Hinge Pins

Sean,



I purchased hinge pin material from ACS - this may be the right number but

you need to check: MS20253-P2-7200 HINGE PIN SS 03-49000.  I see no

advantage to stainless steel over the standard steel pins.



I got (2) 6' lengths as I install the cowl side pins from inside the

cockpit.  The pins run through a piece of 1/4" aluminum tubing on the cabin

side of the firewall that acts as a conduit.  I took a 3/16" round head

rivet and drilled a 1/16" hole through the center, then countersunk the

shank end, cut off the head, and JB welded the rivet into one end of the

1/4" tubing (countersunk part to the inside so the pin is directed into the

1/16" hole).  A 3/16" hole is drilled into the firewall such that the rivet

shank pokes through 1/4" or so, in a spot such that the pin is directed into

the first eyelet on the cowl.



This is really a lot simpler than it sounds.  The end result is with a few

AN fittings you have lockable side pins that don't poke through the front of

the cowl.



Carl



--

schmoboy

Joined: 26 Feb 2006
Posts: 130

Posted: Sat Dec 15, 2012 3:10 pm Post subject: Cowl Hinge Pins

Thanks Carl.



I assumed it was "required" to replace them with the part mentioned in 

the plans, but I am now seeing that is not the case.



I shamelessly stole the pin retainer from Mike 

(http://www.azcloudflyer.com/finish/IMG_0298.jpg).  And it seems the 

pins that come with the hinges will be fine.



-Sean #40303



On 12/15/12 3:39 PM, Carl Froehlich wrote:

[quote] 



 Sean,



 I purchased hinge pin material from ACS - this may be the right number but

 you need to check: MS20253-P2-7200 HINGE PIN SS 03-49000.  I see no

 advantage to stainless steel over the standard steel pins.



 I got (2) 6' lengths as I install the cowl side pins from inside the

 cockpit.  The pins run through a piece of 1/4" aluminum tubing on the cabin

 side of the firewall that acts as a conduit.  I took a 3/16" round head

 rivet and drilled a 1/16" hole through the center, then countersunk the

 shank end, cut off the head, and JB welded the rivet into one end of the

 1/4" tubing (countersunk part to the inside so the pin is directed into the

 1/16" hole).  A 3/16" hole is drilled into the firewall such that the rivet

 shank pokes through 1/4" or so, in a spot such that the pin is directed into

 the first eyelet on the cowl.



 This is really a lot simpler than it sounds.  The end result is with a few

 AN fittings you have lockable side pins that don't poke through the front of

 the cowl.



 Carl



 --

Greg McFarlane

Joined: 12 Apr 2012
Posts: 57
Location: Albany Western Australia

Posted: Sun Dec 16, 2012 3:01 am Post subject: Re: Cowl Hinge Pins

Re conduit for cabin side entry of side cowl hinges, rather than use 1/4 inch ally pipe, if you go to your local auto brake place you'll be able to purchase steel brake pipe that the side pins are a neat fit in. Then it's only a matter of drilling a hole in the firewall and fwd fuse bulkhead F-1002-R that is a neat fit for the steel pipe and lines up with the side cowl hinges, bond with bondo or epoxy. I've kept mine straight just below the vents but you can bend the pipe to any location and the pin will happily follow. Epoxy a rivit into the last forward piano hinge, top or bottom to stop the pin from making friends with your fan.  Cheers from Western Australia.

jesse(at)saintaviation.co
Guest

Posted: Mon Dec 17, 2012 12:26 pm Post subject: Cowl Hinge Pins

You will be very happy that you bought the pins from Van's if you do. The welded on tab makes it much easier to remove the pins and keeps them very securely. Just using an eyelet to hold the tip of the pin is not nearly as nice, IMHO.



YMMV



Jesse Saint

Saint Aviation, Inc.

jesse(at)saintaviation.com

C: 352-427-0285

F: 815-377-3694



On Dec 15, 2012, at 11:32 AM, Sean Stephens <sean(at)stephensville.com> wrote:



 	  Quote: 	
		   

 

 Anyone know a source for the stainless hinge pins besides Vans?  I don't understand why they don't provide enough for the side hinges between the top and bottom cowl.  Page 47-8 says they are available from the accessories catalog.  I'd think they are more than just accessories.  I understand that they weld on a retainer for these "accessories", but one would think that it would be supplied in the kit.

 

 -Sean #40303

Tim Olson

Joined: 25 Jan 2007
Posts: 2872

Posted: Mon Dec 17, 2012 7:16 pm Post subject: Cowl Hinge Pins

Amen to that Jesse!  I had just the hing section for a long long

time, and while it did work, eventually the eyelet widens and the

pin can start to move and then the wear happens faster yet.

I did the JB weld thing for a while to hold it on, and that worked

ok for a while but soon one of them broke free and then I had to

re-glue it. Finally I got ticked off enough that I did it better.

I bought new pins, and a section of stainless hinge, and silver

soldered them together. Yes, Van's does sell a pre-made pin, but

by this point I was irritated and knew I could do a better job

if I took the time.  Wish I would have had Van's pins right from

the start.  Actually, if I could do it all over again, I'd

make mine look like Sean's where the pins get hidden by an

oval shaped RV-10 logo. That to me trims it out perfectly.

Tim Olson - RV-10 N104CD

On 12/17/2012 2:26 PM, Jesse Saint wrote:

 	  Quote: 	

 <jesse(at)saintaviation.com>

 You will be very happy that you bought the pins from Van's if you do.

 The welded on tab makes it much easier to remove the pins and keeps

 them very securely. Just using an eyelet to hold the tip of the pin

 is not nearly as nice, IMHO.

 YMMV

 Jesse Saint Saint Aviation, Inc. jesse(at)saintaviation.com C:

 352-427-0285 F: 815-377-3694

 On Dec 15, 2012, at 11:32 AM, Sean Stephens <sean(at)stephensville.com>

 wrote:

> 

> <sean(at)stephensville.com>

>

> Anyone know a source for the stainless hinge pins besides Vans?  I

> don't understand why they don't provide enough for the side hinges

> between the top and bottom cowl.  Page 47-8 says they are available

> from the accessories catalog.  I'd think they are more than just

> accessories.  I understand that they weld on a retainer for these

> "accessories", but one would think that it would be supplied in the

> kit.

>

> -Sean #40303

aerosport1

Joined: 07 Nov 2007
Posts: 231

Posted: Tue Dec 18, 2012 1:35 pm Post subject: Cowl Hinge Pins

Here are the covers Tim was referring to. These are produced by Aerosport

Products.

Geoff Combs 

Aerosport 

8090 howe industrial pkwy

canal winchester, ohio 43110

614.834.5227p

614.834.5230f

www.aerosportmodeling.com



--

IMG_3384.JPG

Description:

Filesize:

28.75 KB

Viewed:

3490 Time(s)

_________________
Geoff Combs
RV-10 QB N829GW
Flying 500 hrs
40033

jdriggs49(at)msn.com
Guest

Posted: Tue Dec 18, 2012 10:10 pm Post subject: Cowl Hinge Pins

Can those be recessed? My buddy left his proud but seems like I've seen pics of them flush???

[quote] From: g.combs@aerosportmodeling.com

 To: rv10-list@matronics.com

 Subject: RE: RV10-List: Cowl Hinge Pins

 Date: Tue, 18 Dec 2012 16:34:01 -0500

 Here are the covers Tim was referring to. These are produced by Aerosport

 Products.

 Geoff Combs 

 Aerosport 

 8090 howe industrial pkwy

 canal winchester, ohio 43110

 614.834.5227p

 614.834.5230f

 www.aerosportmodeling.com

 --

rleffler

Joined: 05 Nov 2006
Posts: 680

Posted: Wed Dec 19, 2012 2:55 am Post subject: Cowl Hinge Pins

By design they are supposed to be recessed and flushed. Here is a link to the instructions.

http://aerosportproducts.com/Docs/cowlpin.pdf



Sent from my iPad



On Dec 19, 2012, at 1:09 AM, Danny Riggs <jdriggs49(at)msn.com (jdriggs49(at)msn.com)> wrote:

[quote]   Can those be recessed? My buddy left his proud but seems like I've seen pics of them flush???



[quote] From: g.combs(at)aerosportmodeling.com (g.combs(at)aerosportmodeling.com)

 To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)

 Subject: RE: Cowl Hinge Pins

 Date: Tue, 18 Dec 2012 16:34:01 -0500

 

 Here are the covers Tim was referring to. These are produced by Aerosport

 Products.

 

 

 Geoff Combs 

 Aerosport 

 8090 howe industrial pkwy

 canal winchester, ohio 43110

 614.834.5227p

 614.834.5230f

 www.aerosportmodeling.com

 

 --

_________________
Bob Leffler
N410BL - Phase I
http://mykitlog.com/rleffler

jdriggs49(at)msn.com
Guest

Posted: Wed Dec 19, 2012 6:29 am Post subject: Cowl Hinge Pins

Thanks!  

Subject: Re: RV10-List: Cowl Hinge Pins

From: rv(at)thelefflers.com

Date: Wed, 19 Dec 2012 05:54:34 -0500

To: rv10-list(at)matronics.com

By design they are supposed to be recessed and flushed. Here is a link to the instructions.

http://aerosportproducts.com/Docs/cowlpin.pdf

Sent from my iPad

On Dec 19, 2012, at 1:09 AM, Danny Riggs <jdriggs49(at)msn.com (jdriggs49(at)msn.com)> wrote:

[quote]   Can those be recessed? My buddy left his proud but seems like I've seen pics of them flush???

[quote] From: g.combs(at)aerosportmodeling.com (g.combs(at)aerosportmodeling.com)

 To: rv10-list(at)matronics.com (rv10-list(at)matronics.com)

 Subject: RE: Cowl Hinge Pins

 Date: Tue, 18 Dec 2012 16:34:01 -0500

 Here are the covers Tim was referring to. These are produced by Aerosport

 Products.

 Geoff Combs 

 Aerosport 

 8090 howe industrial pkwy

 canal winchester, ohio 43110

 614.834.5227p

 614.834.5230f

 www.aerosportmodeling.com

 --

Display posts from previous:

	Matronics Email Lists Forum Index -> RV10-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum