Matronics Email Lists :: View topic - firewall engine fittings (CH601-HD )

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

firewall engine fittings (CH601-HD )

Matronics Email Lists Forum Index -> Zenith-List

View previous topic :: View next topic

Author Message

carlossa52(at)gmail.com
Guest

Posted: Sun May 19, 2013 10:00 am Post subject: firewall engine fittings (CH601-HD )

Hello, folks

Can someone clear this for me:

The CH601-HD drawings show the lower firewall engine fitting (6F6-3)  with two holes for bolts going through the floor (and extrusion 6F5-4). The forward hole is 18 mm from the forward edge of the fitting.

  

Issues: (1) The firewall flange is 18 mm wide, and even considering that the thickness of the doubler will position the bolt hole a little farther away from the firewall web, the hole will still touch the firewall flange.

  

And (2) drawing 6F9 shows the forward bolt going through the lower firewall doubler (and presumably through the firewall flange). 

I haven't found pictures that clearly show where this bolt was installed by others.

  



Any comments?



Thanks in advance

Carlos



CH601-HD, plans



  [quote][b]

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

jaybannist(at)cs.com
Guest

Posted: Sun May 19, 2013 10:39 am Post subject: firewall engine fittings (CH601-HD )

Carlos,

 

 This is a photo of my 601XL under construction.  I don't think it would be that much different from your HD.  It clearly shows the forward bolt hole (with cleco) going through the firewall flange.  As I recall, because of the proximity of the bolt heads, the engine mount bolt had to be inserted and tacked into place before the forward bracket bolt was installed.

 

 Jay

  

     

  

    --

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

Zodiac07-13-06_005a.jpg

Description:

Filesize:

139.02 KB

Viewed:

4134 Time(s)

entecrj(at)sbcglobal.net
Guest

Posted: Sun May 19, 2013 1:07 pm Post subject: firewall engine fittings (CH601-HD )

Carlos:

  

 I will look for a picture of my engine fitting, I fabricated a shim to fit  under the engine fitting to level it out.

  

 Russell Johnson

    

  From: Carlos Sa (carlossa52(at)gmail.com) 

 Sent: Sunday, May 19, 2013 12:59 PM

 To: zenith-list(at)matronics.com (zenith-list(at)matronics.com) 

 Subject: firewall engine fittings (CH601-HD  )

  



          Hello, folks



 

Can someone clear this for me:

The CH601-HD drawings show  the lower firewall engine fitting (6F6-3)  with two holes for bolts going  through the floor (and extrusion 6F5-4). The forward hole is 18 mm from the  forward edge of the fitting.



Issues: (1) The firewall flange is 18 mm  wide, and even considering that the thickness of the doubler will position the  bolt hole a little farther away from the firewall web, the hole will still touch  the firewall flange.



And (2) drawing 6F9 shows the forward bolt going  through the lower firewall doubler (and presumably through the firewall flange).  

I haven't found pictures that clearly show where this bolt was  installed by others.

Any comments?



Thanks in  advance

Carlos



CH601-HD, plans



[quote]



href="http://www.matronics.com/Navigator?Zenith-List">http://www.matronhref="http://forums.matronics.com">http://forums.matronics.com

href="http://www.matronics.com/contribution">http://www.matronics.com/c

[b]

- The Matronics Zenith-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Zenith-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Zenith-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum