Matronics Email Lists :: View topic - Final filter position.

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Final filter position.

Matronics Email Lists Forum Index -> Yak-List

View previous topic :: View next topic

Author Message

brad(at)runawaymedia.co.z
Guest

Posted: Fri Jun 14, 2013 6:49 am Post subject: Final filter position.

This is the final position of the oil filter . Thanks to all who contributed to my project. 

Please ignore the rudimentary bracket mounting its under review. 

Best regards Bradly Banks

Sent from Samsung Mobile

- The Matronics Yak-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

20130614_115250_resized_1.jpg

Description:

Filesize:

180.91 KB

Viewed:

1766 Time(s)

20130614_115300_resized.jpg

Description:

Filesize:

182.18 KB

Viewed:

1766 Time(s)

dsavarese0812(at)bellsout
Guest

Posted: Fri Jun 14, 2013 7:03 am Post subject: Final filter position.

Bradly,

FYI, it is not recommended to use nylon or fiber locking nuts under the 

cowl due to heat.  I think the reason are obvious.  You may want to 

replace them with steel lock nuts.

Dennis



A. Dennis Savarese

334-285-6263

334-546-8182 (mobile)

www.yak-52.com

Skype - Yakguy1



On 6/14/2013 9:45 AM, Bradly Banks wrote:

 	  Quote: 	
		   This is the final position of the oil filter . Thanks to all who 

 contributed to my project.

 Please ignore the rudimentary bracket mounting its under review.



 Best regards Bradly Banks



 Sent from Samsung Mobile

- The Matronics Yak-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

wlannon(at)shaw.ca
Guest

Posted: Sat Jun 15, 2013 7:37 pm Post subject: Final filter position.

--

- The Matronics Yak-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

wlannon(at)shaw.ca
Guest

Posted: Sun Jun 16, 2013 9:13 am Post subject: Final filter position.

Hi Dennis;



There is no prohibition as such for the use of TSO'D (AN365 or MS20365, etc) 

nylon self locking nuts under the cowling.  They are approved to a 

temperature of 250 deg.F (120 deg.C) and certainly would not be used on 

exhaust systems, too close to cylinders or other high temperature areas. 

But there are many locations where they are quite acceptable.  They are 

approved for control rod end fittings that incorporate a bearing assembly 

where the nut is tightened on the inner race.  They are NOT approved in a 

similar location where the bolt is the bearing.



Cheers;

Walt



--

- The Matronics Yak-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

dsavarese0812(at)bellsout
Guest

Posted: Mon Jun 17, 2013 3:57 am Post subject: Final filter position.

Thank you Walt for enlightening me.

Dennis  

From: Walter Lannon <wlannon(at)shaw.ca>

To: yak-list(at)matronics.com

Sent: Sun, June 16, 2013 12:13:29 PM

Subject: Re: Final filter position.

 --> Yak-List message posted by: "Walter Lannon" <wlannon(at)shaw.ca (wlannon(at)shaw.ca)>

Hi Dennis;

There is no prohibition as such for the use of TSO'D (AN365 or MS20365, etc) nylon self locking nuts under the cowling.  They are approved to a temperature of 250 deg.F (120 deg.C) and certainly would not be used on exhaust systems, too close to cylinders or other high temperature areas. But there are many locations where they are quite acceptable.  They are approved for control rod end fittings that incorporate a bearing assembly where the nut is tightened on the inner race.  They are NOT approved in a similar location where the bolt is the bearing.

Cheers;

Walt

--

- The Matronics Yak-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

Display posts from previous:

	Matronics Email Lists Forum Index -> Yak-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum