Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

CONTACT EXTRACTOR

Matronics Email Lists Forum Index -> AeroElectric-List

View previous topic :: View next topic

Author Message

racerjerry

Joined: 15 Dec 2009
Posts: 202
Location: Deer Park, NY

Posted: Sun Nov 03, 2013 8:09 am Post subject: CONTACT EXTRACTOR

Can someone give me the (working tip end) dimensions of the Bendix/King contact extraction tool p/n 047-05099-001 that is used to remove contacts p/n 030-01107-00xx as used on KT 76 and KX 155.  Please – no guesses – I need a caliper on this one.  I will be working under extremely difficult conditions.  



Apparently, this tool is also known as Molex p/n HT-1884

Thank you for your help.

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

_________________
Jerry King

nuckolls.bob(at)aeroelect
Guest

Posted: Mon Nov 04, 2013 11:19 am Post subject: CONTACT EXTRACTOR

At 10:09 AM 11/3/2013, you wrote:

  	  Quote: 	
		  --> AeroElectric-List message posted by: "racerjerry" <gki(at)suffolk.lib.ny.us>



 Can someone give me the (working tip end) dimensions of the Bendix/King contact extraction tool p/n 047-05099-001 that is used to remove contacts p/n 030-01107-00xx as used on KT 76 and KX 155.  Please – no guesses – I need a caliper on this one.  I will be working under extremely difficult conditions.  



 Apparently, this tool is also known as Molex p/n HT-1884

 Thank you for your help. 	


    How many terminals do you need to extract?

    The tool size is not critical . . . it needs

    to fit inside the width of the slot in the

    connector housing and be no thicker than the

    depth of the slot. It's a thin blade that

    is used to depress the retention tang

    on the pin.



  

 [img]cid:7.1.0.9.0.20131104131604.049c16c0(at)aeroelectric.com.0[/img] 



 

 

    Unless you have bunch of terminals to pull,

    suggest you try a sewing needle inserted into

    the center of the slot. The tang is only about

    .4" inside and not hard to reach.



   Bob . . .

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

a24342c.jpg

Description:

Filesize:

12.17 KB

Viewed:

4471 Time(s)

racerjerry

Joined: 15 Dec 2009
Posts: 202
Location: Deer Park, NY

Posted: Mon Nov 04, 2013 12:11 pm Post subject: Re: CONTACT EXTRACTOR

Bob, Thank you for your response.  Fortunately, I have only two terminals to extract.  

I was hoping to get measurements of the actual tool; especially the blade thickness, so the contact would release easily, yet I wouldn’t have to worry about permanently deforming the retainer clip.  Also, I don’t have a spare Bendix/King card edge connector body to give me the slot width, but I could probably guesstimate that.



My idea was to cut a sliver of shim stock.  Do YOU have a guess as to blade thickness of this tool?



Yes, I may have to resort to the sewing needle approach, but I don’t know if these old eyes will be able to keep the needle centered in the slot.  Besides, trying different sizes, I can ruin only so many of my wife’s sewing needles before there is hell to pay.



Thanks again,



Jerry King

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

_________________
Jerry King

nuckolls.bob(at)aeroelect
Guest

Posted: Mon Nov 04, 2013 3:51 pm Post subject: CONTACT EXTRACTOR

At 02:11 PM 11/4/2013, you wrote:

 	  Quote: 	
		  



Bob, Thank you for your response.  Fortunately, 

I have only two terminals to extract.

I was hoping to get measurements of the actual 

tool; especially the blade thickness, so the 

contact would release easily, yet I wouldn’t 

have to worry about permanently deforming the retainer clip.


	


   There is possibility of 'flattening' the

   clip even when the 'right tool' is used.

   I always tweak the clip to increase it's

   grip before re-inserting a used terminal

   back into the housing.



 	  Quote: 	
		     Also, I don’t have a spare Bendix/King card 

 edge connector body to give me the slot width, 

 but I could probably guesstimate that.


	


   I don't think I've ever actually measured one.

   The last two that I made were fabricated from

   flat spring stock cabbaged from a pocket tape

   measure. I used a cutoff wheel in a Dremel to

   sculpt the material.



   Many moons ago I published this offering



Vhttp://tinyurl.com/nknv4bk



   I believe these numbers were suited to

   the various versions of this pin retention

   methodology . . . but that was some time ago.

 	  Quote: 	
		  Yes, I may have to resort to the sewing needle 

approach, but I don’t know if these old eyes 

will be able to keep the needle centered in the 

slot.  Besides, trying different sizes, I can 

ruin only so many of my wife’s sewing needles before there is hell to pay.


	


   Get your own needles. In fact, I think

   sewing machine needles are about the right

   thickness and they offer a 'handle' of sorts

   on the machine end. Again, a little sculpting

   with a Dremel would tailor them to the task.

   Bob . . .

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

klehman(at)albedo.net
Guest

Posted: Mon Nov 04, 2013 5:15 pm Post subject: CONTACT EXTRACTOR

I find that one of my very small flat screwdrivers (watchmaker type) 

often works well on these types of pins.

Ken



On 04/11/2013 6:50 PM, Robert L. Nuckolls, III wrote:

 	  Quote: 	
		   

 <nuckolls.bob(at)aeroelectric.com>



 At 02:11 PM 11/4/2013, you wrote:

> 

> <gki(at)suffolk.lib.ny.us>

>

> Bob, Thank you for your response.  Fortunately, I have only two

> terminals to extract.

> I was hoping to get measurements of the actual tool; especially the

> blade thickness, so the contact would release easily, yet I wouldn’t

> have to worry about permanently deforming the retainer clip.



    There is possibility of 'flattening' the

    clip even when the 'right tool' is used.

    I always tweak the clip to increase it's

    grip before re-inserting a used terminal

    back into the housing.



>   Also, I don’t have a spare Bendix/King card edge connector body to

> give me the slot width, but I could probably guesstimate that.



    I don't think I've ever actually measured one.

    The last two that I made were fabricated from

    flat spring stock cabbaged from a pocket tape

    measure. I used a cutoff wheel in a Dremel to

    sculpt the material.



    Many moons ago I published this offering



 Vhttp://tinyurl.com/nknv4bk



    I believe these numbers were suited to

    the various versions of this pin retention

    methodology . . . but that was some time ago.

> Yes, I may have to resort to the sewing needle approach, but I don’t

> know if these old eyes will be able to keep the needle centered in the

> slot.  Besides, trying different sizes, I can ruin only so many of my

> wife’s sewing needles before there is hell to pay.



    Get your own needles. In fact, I think

    sewing machine needles are about the right

    thickness and they offer a 'handle' of sorts

    on the machine end. Again, a little sculpting

    with a Dremel would tailor them to the task.

    Bob . . .




	


---

This email is free from viruses and malware because avast! Antivirus protection is active.

http://www.avast.com

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

racerjerry

Joined: 15 Dec 2009
Posts: 202
Location: Deer Park, NY

Posted: Tue Nov 05, 2013 3:09 am Post subject: Re: CONTACT EXTRACTOR

OK, I am armed.  Wife gave me an assortment of different size sewing machine needles (much better to not stab yourself with) and I also raided my collection of jewelers screwdrivers.  Now, if I could only see the back of the connector to tell which wire is which…



Bob & Ken, thank you very much for the tips.

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

_________________
Jerry King

Display posts from previous:

	Matronics Email Lists Forum Index -> AeroElectric-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum