Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

M-14P Generator Brushes

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Yak-List
View previous topic :: View next topic  
Author Message
Mike Bell



Joined: 10 Jan 2006
Posts: 51
PostPosted: Tue Jun 13, 2006 9:07 am    Post subject: M-14P Generator Brushes Reply with quote
The generator brushes on my Yak-52 are almost worn enough to replace. The M-14 manual says to not replace them without removing the generator. It looks like there's barely enough room to get in there without removing the generator. Anybody have experience with this?

Also, is there any particular break-in required after brush replacement?

Thanks,
Mike

- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

_________________
Mike Bell
Elk Grove, CA
avbell2(at)comcastdotnet
Back to top
View user's profile Send private message
mark.bitterlich(at)navy.m
Guest
PostPosted: Tue Jun 13, 2006 9:21 am    Post subject: M-14P Generator Brushes Reply with quote
I can tell you that pulling the generator out is a piece of cake. Do not unbolt it from the adapter plate (6 nuts) ... remove the generator and the adapter plate as one piece. (4 nuts) Will take you about 30 minutes or LESS. As far as break-in goes, as long as you can spin the generator shaft and the brushes remain in one piece.. you're good to go. "Break-In" (per se) happens in the first few seconds after engine start.

Mark Bitterlich
--

- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List
Back to top
rvfltd(at)televar.com
Guest
PostPosted: Tue Jun 13, 2006 9:29 am    Post subject: M-14P Generator Brushes Reply with quote
Mike,
After you replace the brushes could you please ship me one of the old
brushes so I can compare it to my stock of 285 hp HS6A generator brushes?
Maybe enclose it with your hoses when you send them to me. Sorry but I
cannot shed any light on the installation as I have never done one myself.

Many thanks.

Always Yakin,
Doug Sapp

--

- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List
Back to top
Mike Bell



Joined: 10 Jan 2006
Posts: 51
PostPosted: Thu Jun 15, 2006 2:30 pm    Post subject: Re: M-14P Generator Brushes Reply with quote
Thanks Mark. With an engine hoist and 3 strong men I will get that megawatt thing off the engine, and send a brush sample to Doug.

- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

_________________
Mike Bell
Elk Grove, CA
avbell2(at)comcastdotnet
Back to top
View user's profile Send private message
rkent(at)wlacrussianeng.c
Guest
PostPosted: Sun Jun 18, 2006 11:48 pm    Post subject: M-14P Generator Brushes Reply with quote
Mike,

I've got generator brushes for the GSR-3000M (brush kits containing 8 new
brushes). If interested, drop me an email or give me a call.

Regards

Rob Kent
Stores Manager
WLAC - Russian Engineering
www.wlacrussianeng.co.uk

Tel: +44 1628 829 165
Fax: +44 1628 828 961

---

- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List
Back to top
mark.bitterlich(at)navy.m
Guest
PostPosted: Tue Jun 20, 2006 7:47 pm    Post subject: M-14P Generator Brushes Reply with quote
Rogo.... it really is easy.... honest!

Mark
--

- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Yak-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group