Matronics Email Lists :: View topic - Dsub Connector Shell With Female Threaded

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Dsub Connector Shell With Female Threaded

Matronics Email Lists Forum Index -> AeroElectric-List

View previous topic :: View next topic

Author Message

billhuntersemail(at)gmail
Guest

Posted: Tue May 30, 2017 6:51 pm Post subject: Dsub Connector Shell With Female Threaded

Hi All,

 

I have a couple of instances where I need to mate a male Dsub to a female Dsub end to end within the length of a wire bundle (example: connect the under panel wire harness to the wire harness of the control stick).

 

I already have the male and female Dsub connectors wired up and they are connected end to end and I have the plastic shells (see below) however the metal screws of the one shell needs to screw into a threaded bore of the other connector so that the two connectors do not disconnect.  Kinda like when you attach the Dsub connector to the back of a computer the plug slides into the receptacle and then the screws on the connector shell thread into the threaded bore of the computer case. 

 

How does one (me) do this on an end to end connector? 

 

 

[img]cid:image002.jpg(at)01D2D97D.DB26FAF0[/img]

 

..

 

Cheers!!!

 

Bill  Hunter

image002.jpg

Description:

Filesize:

11.53 KB

Viewed:

10387 Time(s)

donvansanten(at)gmail.com
Guest

Posted: Tue May 30, 2017 7:23 pm Post subject: Dsub Connector Shell With Female Threaded

multiple ways to to this1 buy one connector with built in nuts (Stein has these) 

2 remove screws and use zip ties to hold the connectors together.

On May 30, 2017 19:56, "William Hunter" <billhuntersemail(at)gmail.com (billhuntersemail(at)gmail.com)> wrote: 	  Quote: 	
		  

Hi All,

 

I have a couple of instances where I need to mate a male Dsub to a female Dsub end to end within the length of a wire bundle (example: connect the under panel wire harness to the wire harness of the control stick).

 

I already have the male and female Dsub connectors wired up and they are connected end to end and I have the plastic shells (see below) however the metal screws of the one shell needs to screw into a threaded bore of the other connector so that the two connectors do not disconnect.  Kinda like when you attach the Dsub connector to the back of a computer the plug slides into the receptacle and then the screws on the connector shell thread into the threaded bore of the computer case. 

 

How does one (me) do this on an end to end connector? 

 

 

[img]cid:image002.jpg(at)01D2D97D.DB26FAF0[/img]

 

..

 

Cheers!!!

 

Bill  Hunter

image002.jpg

Description:

Filesize:

11.53 KB

Viewed:

10387 Time(s)

enginerdy(at)gmail.com
Guest

Posted: Tue May 30, 2017 7:27 pm Post subject: Dsub Connector Shell With Female Threaded

I think you want something like this female screw kit:



http://www.mouser.com/search/ProductDetail.aspx?qs=5KjJMQyy%252baNdw8WXWxtgeQ%3d%3d



It attaches to the contact portion before you install the back shell. Each one should contain a kit for one connector pair, and you can just use the provided male threaded hardware with the other one.



Be careful to either tighten the female nuts adequately or use some Loctite to keep the nuts from falling out if you ever need to separate the two connectors.



Here is a similar part from SteinAir

http://www.steinair.com/product/dsub-nut-pack-4-40-thread-size/



or you can also buy one with built in female lugs like this: 

http://www.steinair.com/product/9-pin-male-dsub-connector-with-4-40-lugs/



These last ones are nice because you never have to worry about the lugs backing out when you take the connectors apart!

 	  Quote: 	
		  On May 30, 2017, at 9:49 PM, William Hunter <billhuntersemail(at)gmail.com (billhuntersemail(at)gmail.com)> wrote:

Hi All,

 

I have a couple of instances where I need to mate a male Dsub to a female Dsub end to end within the length of a wire bundle (example: connect the under panel wire harness to the wire harness of the control stick).

 

I already have the male and female Dsub connectors wired up and they are connected end to end and I have the plastic shells (see below) however the metal screws of the one shell needs to screw into a threaded bore of the other connector so that the two connectors do not disconnect.  Kinda like when you attach the Dsub connector to the back of a computer the plug slides into the receptacle and then the screws on the connector shell thread into the threaded bore of the computer case. 

 

How does one (me) do this on an end to end connector? 

 

 

<image002.jpg>

 

..

 

Cheers!!!

 

Bill  Hunter

art(at)zemon.name
Guest

Posted: Tue May 30, 2017 7:44 pm Post subject: Dsub Connector Shell With Female Threaded

Bill,



I hate those screws. I have seen barrel connectors which are female on both ends, stuck between two D-sub shells. They require having a screwdriver on both ends, Pain-in-the-a**.

I am planning to use a pair a zip ties in a X in the places where I have D-sub connectors in my plane. I would rather cut and replace the zip ties than mess around with the screws.

I will be really interested to see if anyone has better ideas.

    -- Art Z.



On Tue, May 30, 2017 at 9:49 PM, William Hunter <billhuntersemail(at)gmail.com (billhuntersemail(at)gmail.com)> wrote:

 	  Quote: 	
		  

Hi All,

 

I have a couple of instances where I need to mate a male Dsub to a female Dsub end to end within the length of a wire bundle (example: connect the under panel wire harness to the wire harness of the control stick).

 

I already have the male and female Dsub connectors wired up and they are connected end to end and I have the plastic shells (see below) however the metal screws of the one shell needs to screw into a threaded bore of the other connector so that the two connectors do not disconnect.  Kinda like when you attach the Dsub connector to the back of a computer the plug slides into the receptacle and then the screws on the connector shell thread into the threaded bore of the computer case. 

 

How does one (me) do this on an end to end connector? 

 

 

[img]cid:image002.jpg(at)01D2D97D.DB26FAF0[/img]

 

..

 

Cheers!!!

 

Bill  Hunter

 

 

 

 



	




-- 

https://CheerfulCurmudgeon.com/"If I am not for myself, who is for me? And if I am only for myself, what am I? And if not now, when?" Hillel

image002.jpg

Description:

Filesize:

11.53 KB

Viewed:

10387 Time(s)

ceengland7(at)gmail.com
Guest

Posted: Wed May 31, 2017 4:35 am Post subject: Dsub Connector Shell With Female Threaded

Google 'dsub latch'. There are several different options for joining dsubs in-line; screws, sliding latches, and spring bales. My favorite style:[url=http://www.newark.com/cooper-interconnect/17-529/d-sub-spring-latch/dp/39F1390?mckv=sPyr8IJjG_dc|pcrid|81605889141|plid||kword||match||slid||product|39F1390|&gross_price=true&CATCI=pla-164504983461&CAAGID=20389674261&CMP=KNC-GUSA-GEN-SHOPPING-39F1390&CAGPSPN=pla&gclid=CjwKEAjw07nJBRDG_tvshefHhWQSJABRcE-ZuxQrtf1Qi0xFg5ATYZXSW2anCtcB-ENzwuu27bdAVhoC_Jfw_wcB&CAWELAID=120185550001138611]http://www.newark.com/cooper-interconnect/17-529/d-sub-spring-latch/dp/39F1390?mckv=sPyr8IJjG_dc|pcrid|81605889141|plid||kword||match||slid||product|39F1390|&gross_price=true&CATCI=pla-164504983461&CAAGID=20389674261&CMP=KNC-GUSA-GEN-SHOPPING-39F1390&CAGPSPN=pla&gclid=CjwKEAjw07nJBRDG_tvshefHhWQSJABRcE-ZuxQrtf1Qi0xFg5ATYZXSW2anCtcB-ENzwuu27bdAVhoC_Jfw_wcB&CAWELAID=120185550001138611[/url]



More positive security than screws, because it can't loosen with vibration. The same latch can be used on chassis mounted connectors, too, as long as the designer left enough room around the connector to add the springs.  (Can you hear me, Advanced Flight Systems?)

Charlie

On Tue, May 30, 2017 at 10:43 PM, Art Zemon <art(at)zemon.name (art(at)zemon.name)> wrote:

 	  Quote: 	
		  Bill,



I hate those screws. I have seen barrel connectors which are female on both ends, stuck between two D-sub shells. They require having a screwdriver on both ends, Pain-in-the-a**.

I am planning to use a pair a zip ties in a X in the places where I have D-sub connectors in my plane. I would rather cut and replace the zip ties than mess around with the screws.

I will be really interested to see if anyone has better ideas.

    -- Art Z.



On Tue, May 30, 2017 at 9:49 PM, William Hunter <billhuntersemail(at)gmail.com (billhuntersemail(at)gmail.com)> wrote:

 	  Quote: 	
		  

Hi All,

 

I have a couple of instances where I need to mate a male Dsub to a female Dsub end to end within the length of a wire bundle (example: connect the under panel wire harness to the wire harness of the control stick).

 

I already have the male and female Dsub connectors wired up and they are connected end to end and I have the plastic shells (see below) however the metal screws of the one shell needs to screw into a threaded bore of the other connector so that the two connectors do not disconnect.  Kinda like when you attach the Dsub connector to the back of a computer the plug slides into the receptacle and then the screws on the connector shell thread into the threaded bore of the computer case. 

 

How does one (me) do this on an end to end connector? 

 

 

[img]cid:image002.jpg(at)01D2D97D.DB26FAF0[/img]

 

..

 

Cheers!!!

 

Bill  Hunter

 

 

 

 



	




-- 

https://CheerfulCurmudgeon.com/"If I am not for myself, who is for me? And if I am only for myself, what am I? And if not now, when?" Hillel

image002.jpg

Description:

Filesize:

11.53 KB

Viewed:

10383 Time(s)

billhuntersemail(at)gmail
Guest

Posted: Wed May 31, 2017 5:52 am Post subject: Dsub Connector Shell With Female Threaded

Thanks everyone for the advice... I came to the right place.  

Bill Hunter  On May 31, 2017 5:40 AM, "Charlie England" <ceengland7(at)gmail.com (ceengland7(at)gmail.com)> wrote: 	  Quote: 	
		  Google 'dsub latch'. There are several different options for joining dsubs in-line; screws, sliding latches, and spring bales. My favorite style:http://www.newark.com/cooper-interconnect/17-529/d-sub-spring-latch/dp/39F1390?mckv=sPyr8IJjG_dc|pcrid|81605889141|plid||kword||match||slid||product|39F1390|&gross_price=true&CATCI=pla-164504983461&CAAGID=20389674261&CMP=KNC-GUSA-GEN-SHOPPING-39F1390&CAGPSPN=pla&gclid=CjwKEAjw07nJBRDG_tvshefHhWQSJABRcE-ZuxQrtf1Qi0xFg5ATYZXSW2anCtcB-ENzwuu27bdAVhoC_Jfw_wcB&CAWELAID=120185550001138611



More positive security than screws, because it can't loosen with vibration. The same latch can be used on chassis mounted connectors, too, as long as the designer left enough room around the connector to add the springs.  (Can you hear me, Advanced Flight Systems?)

Charlie

On Tue, May 30, 2017 at 10:43 PM, Art Zemon <art(at)zemon.name (art(at)zemon.name)> wrote:

 	  Quote: 	
		  Bill,



I hate those screws. I have seen barrel connectors which are female on both ends, stuck between two D-sub shells. They require having a screwdriver on both ends, Pain-in-the-a**.

I am planning to use a pair a zip ties in a X in the places where I have D-sub connectors in my plane. I would rather cut and replace the zip ties than mess around with the screws.

I will be really interested to see if anyone has better ideas.

    -- Art Z.



On Tue, May 30, 2017 at 9:49 PM, William Hunter <billhuntersemail(at)gmail.com (billhuntersemail(at)gmail.com)> wrote:

 	  Quote: 	
		  

Hi All,

 

I have a couple of instances where I need to mate a male Dsub to a female Dsub end to end within the length of a wire bundle (example: connect the under panel wire harness to the wire harness of the control stick).

 

I already have the male and female Dsub connectors wired up and they are connected end to end and I have the plastic shells (see below) however the metal screws of the one shell needs to screw into a threaded bore of the other connector so that the two connectors do not disconnect.  Kinda like when you attach the Dsub connector to the back of a computer the plug slides into the receptacle and then the screws on the connector shell thread into the threaded bore of the computer case. 

 

How does one (me) do this on an end to end connector? 

 

 

[img]cid:image002.jpg(at)01D2D97D.DB26FAF0[/img]

 

..

 

Cheers!!!

 

Bill  Hunter

 

 

 

 



	




-- 

https://CheerfulCurmudgeon.com/"If I am not for myself, who is for me? And if I am only for myself, what am I? And if not now, when?" Hillel

image002.jpg

Description:

Filesize:

11.53 KB

Viewed:

10382 Time(s)

donjohnston

Joined: 13 Dec 2009
Posts: 231

Posted: Thu Jun 01, 2017 6:28 am Post subject: Re: Dsub Connector Shell With Female Threaded

Easier link: 

https://tinyurl.com/y9mhl2j5



  



 	  ceengland7(at)gmail.com wrote: 	
		  My favorite style:[url=http://www.newark.com/cooper-interconnect/17-529/d-sub-spring-latch/dp/39F1390?mckv=sPyr8IJjG_dc|pcrid|81605889141|plid||kword||match||slid||product|39F1390|&gross_price=true&CATCI=pla-164504983461&CAAGID=20389674261&CMP=KNC-GUSA-GEN-SHOPPING-39F1390&CAGPSPN=pla&gclid=CjwKEAjw07nJBRDG_tvshefHhWQSJABRcE-ZuxQrtf1Qi0xFg5ATYZXSW2anCtcB-ENzwuu27bdAVhoC_Jfw_wcB&CAWELAID=120185550001138611]http://www.newark.com/cooper-interconnect/17-529/d-sub-spring-latch/dp/39F1390?mckv=sPyr8IJjG_dc|pcrid|81605889141|plid||kword||match||slid||product|39F1390|&gross_price=true&CATCI=pla-164504983461&CAAGID=20389674261&CMP=KNC-GUSA-GEN-SHOPPING-39F1390&CAGPSPN=pla&gclid=CjwKEAjw07nJBRDG_tvshefHhWQSJABRcE-ZuxQrtf1Qi0xFg5ATYZXSW2anCtcB-ENzwuu27bdAVhoC_Jfw_wcB&CAWELAID=120185550001138611[/url]

ceengland7(at)gmail.com
Guest

Posted: Thu Jun 01, 2017 11:52 am Post subject: Dsub Connector Shell With Female Threaded

Which buries the destination, so you don't know where you're going when 

you click it.

:-0



On 6/1/2017 9:28 AM, donjohnston wrote:

 	  Quote: 	
		   



 Easier link:

 https://tinyurl.com/y9mhl2j5



   [Wink]

 ceengland7(at)gmail.com wrote:

> My favorite style:http://www.newark.com/cooper-interconnect/17-529/d-sub-spring-latch/dp/39F1390?mckv=sPyr8IJjG_dc|pcrid|81605889141|plid||kword||match||slid||product|39F1390|&gross_price=true&CATCI=pla-164504983461&CAAGID 389674261&CMP=KNC-GUSA-GEN-SHOPPING-39F1390&CAGPSPN=pla&gclid=CjwKEAjw07nJBRDG_tvshefHhWQSJABRcE-ZuxQrtf1Qi0xFg5ATYZXSW2anCtcB-ENzwuu27bdAVhoC_Jfw_wcB&CAWELAID=120185550001138611 (http://www.newark.com/cooper-interconnect/17-529/d-sub-spring-latch/dp/39F1390?mckv=sPyr8IJjG_dc|pcrid|81605889141|plid||kword||match||slid||product|39F1390|&gross_price=true&CATCI=pla-164504983461&CAAGID 389674261&CMP=KNC-GUSA-GEN-SHOPPING-39F1390&CAGPSPN=pla&gclid=CjwKEAjw07nJBRDG_tvshefHhWQSJABRcE-ZuxQrtf1Qi0xFg5ATYZXSW2anCtcB-ENzwuu27bdAVhoC_Jfw_wcB&CAWELAID=120185550001138611)

>




	




---

This email has been checked for viruses by Avast antivirus software.

https://www.avast.com/antivirus

donjohnston

Joined: 13 Dec 2009
Posts: 231

Posted: Sat Jun 03, 2017 2:54 pm Post subject: Re: Dsub Connector Shell With Female Threaded

Not really.  I just made a clickable link from your URL.  So the destination is newark.com. 



Trying to copy/paste that long URL with a phone or tablet is a pain. 



But hey, whatever stirs your grits. 

 	  ceengland7(at)gmail.com wrote: 	
		  Which buries the destination, so you don't know where you're going when 

you click it.

:-0



On 6/1/2017 9:28 AM, donjohnston wrote:

 	  Quote: 	
		   



 Easier link:

 https://tinyurl.com/y9mhl2j5



   [Wink]

 ceengland7(at)gmail.com wrote:

> My favorite style:http://www.newark.com/cooper-interconnect/17-529/d-sub-spring-latch/dp/39F1390?mckv=sPyr8IJjG_dc|pcrid|81605889141|plid||kword||match||slid||product|39F1390|&gross_price=true&CATCI=pla-164504983461&CAAGID 389674261&CMP=KNC-GUSA-GEN-SHOPPING-39F1390&CAGPSPN=pla&gclid=CjwKEAjw07nJBRDG_tvshefHhWQSJABRcE-ZuxQrtf1Qi0xFg5ATYZXSW2anCtcB-ENzwuu27bdAVhoC_Jfw_wcB&CAWELAID=120185550001138611 (http://www.newark.com/cooper-interconnect/17-529/d-sub-spring-latch/dp/39F1390?mckv=sPyr8IJjG_dc|pcrid|81605889141|plid||kword||match||slid||product|39F1390|&gross_price=true&CATCI=pla-164504983461&CAAGID 389674261&CMP=KNC-GUSA-GEN-SHOPPING-39F1390&CAGPSPN=pla&gclid=CjwKEAjw07nJBRDG_tvshefHhWQSJABRcE-ZuxQrtf1Qi0xFg5ATYZXSW2anCtcB-ENzwuu27bdAVhoC_Jfw_wcB&CAWELAID=120185550001138611)

>

enginerdy(at)gmail.com
Guest

Posted: Sat Jun 03, 2017 3:13 pm Post subject: Dsub Connector Shell With Female Threaded

More to the point, you can win a free glass panel for your airplane by going here: http://bit.ly/2lHA1xP

 	  Quote: 	
		  On Jun 3, 2017, at 5:54 PM, donjohnston <don(at)velocity-xl.com (don(at)velocity-xl.com)> wrote:

--> AeroElectric-List message posted by: "donjohnston" <don(at)velocity-xl.com (don(at)velocity-xl.com)>Not really.  I just made a clickable link from your URL.  So the destination is newark.com. Trying to copy/paste that long URL with a phone or tablet is a pain. But hey, whatever stirs your grits. ceengland7(at)gmail.com wrote: 	  Quote: 	
		  Which buries the destination, so you don't know where you're going when you click it.:-0On 6/1/2017 9:28 AM, donjohnston wrote: 	  Quote: 	
		   Easier link: https://tinyurl.com/y9mhl2j5   [Wink] ceengland7(at)gmail.com wrote: 	  Quote: 	
		  My favorite style:[url=http://www.newark.com/cooper-interconnect/17-529/d-sub-spring-latch/dp/39F1390?mckv=sPyr8IJjG_dc|pcrid|81605889141|plid||kword||match||slid||product|39F1390|&gross_price=true&CATCI=pla-164504983461&CAAGID]http://www.newark.com/cooper-interconnect/17-529/d-sub-spring-latch/dp/39F1390?mckv=sPyr8IJjG_dc|pcrid|81605889141|plid||kword||match||slid||product|39F1390|&gross_price=true&CATCI=pla-164504983461&CAAGID[/url] 389674261&CMP=KNC-GUSA-GEN-SHOPPING-39F1390&CAGPSPN=pla&gclid=CjwKEAjw07nJBRDG_tvshefHhWQSJABRcE-ZuxQrtf1Qi0xFg5ATYZXSW2anCtcB-ENzwuu27bdAVhoC_Jfw_wcB&CAWELAID=120185550001138611 ([url=http://www.newark.com/cooper-interconnect/17-529/d-sub-spring-latch/dp/39F1390?mckv=sPyr8IJjG_dc|pcrid|81605889141|plid||kword||match||slid||product|39F1390|&gross_price=true&CATCI=pla-164504983461&CAAGID]http://www.newark.com/cooper-interconnect/17-529/d-sub-spring-latch/dp/39F1390?mckv=sPyr8IJjG_dc|pcrid|81605889141|plid||kword||match||slid||product|39F1390|&gross_price=true&CATCI=pla-164504983461&CAAGID[/url] 389674261&CMP=KNC-GUSA-GEN-SHOPPING-39F1390&CAGPSPN=pla&gclid=CjwKEAjw07nJBRDG_tvshefHhWQSJABRcE-ZuxQrtf1Qi0xFg5ATYZXSW2anCtcB-ENzwuu27bdAVhoC_Jfw_wcB&CAWELAID=120185550001138611) 	
	
	
Read this topic online here:http://forums.matronics.com/viewtopic.php?p=469813#469813

Eric Page

Joined: 15 Feb 2017
Posts: 245

Posted: Sat Jun 03, 2017 3:51 pm Post subject: Dsub Connector Shell With Female Threaded

I think his point is that the Tinyurl link obfuscates the destination that you'll reach when you click it.  It might be benign, or it might not.  Many people, myself included, will not click a link without knowing what's likely to be at the other end of the DNS rabbit hole.



Tinyurl provides the option of using preview links that begin with preview.tinyurl.com.  Those links take you to the tinyurl website where you can see the full un-shortened URL and decide whether you want to go further.  Very handy for posting in forums like this one.



Eric

 	  Quote: 	
		   On Jun 3, 2017, at 5:54 PM, donjohnston <don(at)velocity-xl.com> wrote:

 

 Not really.  I just made a clickable link from your URL.  So the destination is newark.com.

ceengland7(at)gmail.com
Guest

Posted: Sat Jun 03, 2017 4:27 pm Post subject: Dsub Connector Shell With Female Threaded

And since we know each other personally, and I know for sure that the 

post came directly from you, and I totally trust that any link I click 

on will not try to attack my computer.....

I know what you did. The problem with those shortened links is that if 

you hover over them to see the destination, it only shows the short-link 

provider; not the actual destination site. So you don't know until you 

get there what site you're actually visiting.

Not sure why you're having to copy/paste. All the phones/tablets I've 

used (both ios & android) allow you to just click on the hyperlink in 

the email client to open the page in the device's browser.

Charlie

On 6/3/2017 5:54 PM, donjohnston wrote:

 	  Quote: 	

 Not really.  I just made a clickable link from your URL.  So the destination is newark.com.

 Trying to copy/paste that long URL with a phone or tablet is a pain.

 But hey, whatever stirs your grits.

 ceengland7(at)gmail.com wrote:

> Which buries the destination, so you don't know where you're going when

> you click it.

> :-0

>

> On 6/1/2017 9:28 AM, donjohnston wrote:

>

>>   

>>

>>   Easier link:

>>   https://tinyurl.com/y9mhl2j5

>>

>>     [Wink]

>>

---

This email has been checked for viruses by Avast antivirus software.

https://www.avast.com/antivirus

donjohnston

Joined: 13 Dec 2009
Posts: 231

Posted: Sat Jun 03, 2017 4:48 pm Post subject: Re: Dsub Connector Shell With Female Threaded

Nor do I. 



My apologies if my attempt to help offended anyone or caused any problems. I shall show myself out now. 



 	  ceengland7(at)gmail.com wrote: 	
		  Not sure why you're having to copy/paste. All the phones/tablets I've used (both ios & android) allow you to just click on the hyperlink in the email client to open the page in the device's browser.



Charlie

screen grab.jpg

Description:

Filesize:

309.99 KB

Viewed:

10313 Time(s)

Display posts from previous:

	Matronics Email Lists Forum Index -> AeroElectric-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum