Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Housai 2350 Redline

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Yak-List
View previous topic :: View next topic  
Author Message
PS



Joined: 08 Sep 2006
Posts: 84
Location: Texas
PostPosted: Tue Jul 10, 2018 7:30 pm    Post subject: Housai 2350 Redline Reply with quote
I have been adjusting blade angle for over a week and have yet to hit redline on the tach. I have adjusted my blades to almost a flat angle and still cannot hit 2350 RPM, my max has been 2250. I checked the small filter on the nosecase and it is clean, I am getting full movement on the actuator with no movement of the cable housing and my tach is accurate. Is my next step moving the arm on the governor?

Phil

- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

_________________
Phil
Back to top
View user's profile Send private message
Harv



Joined: 01 Jul 2010
Posts: 172
PostPosted: Thu Jul 12, 2018 2:44 am    Post subject: Re: Housai 2350 Redline Reply with quote
Phil

I had a similar issue initially as the AC came from the PLA and couldn’t quite get to the redline rpm.

I moved the governor stop and that made a little difference but it was unpredictable and that’s when we noticed the teleflex cable clamp which is plastic (located located up on the gill shutter frame) was cracked and allowing the outer tube to move. We remade this part in Ali

Check that first and let us know.

Rgs
Harv

- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List
Back to top
View user's profile Send private message
PS



Joined: 08 Sep 2006
Posts: 84
Location: Texas
PostPosted: Thu Jul 12, 2018 3:49 am    Post subject: Re: Housai 2350 Redline Reply with quote
I checked the cable housing attach, it is fine. I will try adjusting the cable length and then move the arm on the governor next.

Thanks

Phil

- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

_________________
Phil
Back to top
View user's profile Send private message
woodja51



Joined: 13 May 2015
Posts: 40
Location: MELBOURNE AUSTRALIA
PostPosted: Thu Jul 12, 2018 4:39 am    Post subject: Re: Housai 2350 Redline Reply with quote
wind the fine pitch governor stop away from the arm a few turns and try again. Set your blade angel back to std of 16 deg+/- .1' and see what happens. That said, 2250 is more than enough power and saves wearing the engine out..Of course your engine is able to produce full power too I would assume?

- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List
Back to top
View user's profile Send private message
PS



Joined: 08 Sep 2006
Posts: 84
Location: Texas
PostPosted: Thu Jul 12, 2018 4:48 am    Post subject: Re: Housai 2350 Redline Reply with quote
I have tried different blade angles and moving the stop. My pitch control needs more travel at the fine pitch setting is my guess. Moving the governor arm a notch may help. I agree, 2250 RPM is plenty of power, but not set by the book which bugs me..I will track this down Confused

Thanks

Phil

- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

_________________
Phil
Back to top
View user's profile Send private message
PS



Joined: 08 Sep 2006
Posts: 84
Location: Texas
PostPosted: Thu Jul 12, 2018 8:37 pm    Post subject: Re: Housai 2350 Redline Reply with quote
I finally moved the splined insert within the governor control arm one spline which gave me 100 RPM more, then it was Miller time.

Thanks to all who offered solutions and suggestions.

- The Matronics Yak-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?Yak-List

_________________
Phil
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> Yak-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group