Matronics Email Lists :: View topic - Water resistant D-Sub

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Water resistant D-Sub

Matronics Email Lists Forum Index -> AeroElectric-List

View previous topic :: View next topic

Author Message

rngurley(at)att.net
Guest

Posted: Tue Apr 16, 2019 9:21 am Post subject: Water resistant D-Sub

Does anyone have a suggestion for a water resistant or waterproof D-Sub connector where the pins are crimped?  I am looking for 5 – 9 pins.

 

Thank you for  your assistance

billhuntersemail(at)gmail
Guest

Posted: Tue Apr 16, 2019 10:59 am Post subject: Water resistant D-Sub

 	  Quote: 	
		   Does anyone have a suggestion for a water resistant or waterproof D-Sub

connector where the pins are crimped?  I am looking for 5 - 9 pins.
	




 



So am I.  Can someone PLEASE suggest a product?

nuckolls.bob(at)aeroelect
Guest

Posted: Tue Apr 16, 2019 11:51 am Post subject: Water resistant D-Sub

At 01:57 PM 4/16/2019, you wrote:

  	  Quote: 	
		  > Does anyone have a suggestion for a water resistant or waterproof D-Sub connector where the pins are crimped?  I am looking for 5 – 9 pins.

  

 So am I.  Can someone PLEASE suggest a product? 	


   There is a mil-qualified 'environmental'

   series of d-subs. See page 364 of this

   catalog



  http://aeroelectric.com/Mfgr_Data/Connectors/ITT_Cannon/Military_Aerospace.pdf

 

   What's the application here? Why 'water

   proof' in a d-sub?



 

 

   Bob . . .

henador_titzoff(at)yahoo.
Guest

Posted: Tue Apr 16, 2019 3:04 pm Post subject: Water resistant D-Sub

Try this link for NorComp Seal-D D-sub connectors that meet IP66 or IP67.  You always have to specify a standard, because otherwise you don't know what you'll get.

Newark, Mouser, Digi-Key and other distributors carry them.



Waterproof D-Sub | IP67/IP68 Rated | NorComp

Waterproof D-Sub | IP67/IP68 Rated | NorComp

Search a full range of waterproof d-sub connectors used in a variety of harsh environments & demanding end-use a...





Henador Titzoff



         



                  

                                                                    On Tuesday, April 16, 2019, 1:36:09 PM EDT, Richard Gurley <rngurley(at)att.net> wrote:                 

                 



                 



                 

Does anyone have a suggestion for a water resistant or waterproof D-Sub connector where the pins are crimped?  I am looking for 5 â€“ 9 pins.

  

Thank you for  your assistance

cluros(at)gmail.com
Guest

Posted: Tue Apr 16, 2019 6:59 pm Post subject: Water resistant D-Sub

https://www.youtube.com/watch?v=qzc4mtFmmHoÂ Â 

On Tue, Apr 16, 2019 at 12:56 PM Robert L. Nuckolls, III <nuckolls.bob(at)aeroelectric.com (nuckolls.bob(at)aeroelectric.com)> wrote:



 	  Quote: 	
		    At 01:57 PM 4/16/2019, you wrote:

  	  Quote: 	
		  > Does anyone have a suggestion for a water resistant or waterproof D-Sub connector where the pins are crimped?Â  I am looking for 5 â€“ 9 pins.

 Â 

 So am I.Â  Can someone PLEASE suggest a product? 	


 Â  There is a mil-qualified 'environmental'

 Â  series of d-subs. See page 364 of this

 Â  catalog



  http://aeroelectric.com/Mfgr_Data/Connectors/ITT_Cannon/Military_Aerospace.pdf

 

 Â  What's the application here? Why 'water

 Â  proof' in a d-sub?



 

 

 Â  Bob . . .

nuckolls.bob(at)aeroelect
Guest

Posted: Wed Apr 17, 2019 8:06 am Post subject: Water resistant D-Sub

At 06:03 PM 4/16/2019, you wrote:

  	  Quote: 	
		  Try this link for NorComp Seal-D D-sub connectors that meet IP66 or IP67.  You always have to specify a standard, because otherwise you don't know what you'll get.



 Newark, Mouser, Digi-Key and other distributors carry them.



  Waterproof D-Sub | IP67/IP68 Rated | NorComp



  

 Waterproof D-Sub | IP67/IP68 Rated | NorComp  



 Search a full range of waterproof d-sub connectors used in a variety of harsh environments & demanding end-use a...

 



 Henador Titzoff

 	


   Cool  find! Thank you.



 

 

   Bob . . .

billhuntersemail(at)gmail
Guest

Posted: Wed Apr 17, 2019 11:58 am Post subject: Water resistant D-Sub

THANKS Bob!!!



 



I bought these DB15 type connectors and I understand the concept of

installing the back shell with the male thumbscrews to connect to an

accessory such as my Lightspeed III ignition module.  



 



What I am not clear on is how to connect the male D-Sub to a female D-Sub

inline with each having a back shell and one with a male thumb screw and the

second with a female threaded nut.  



 



Example:  I have a Dynon GPS antenna mounted to a removeable hatch and I

want to be able to unbolt the hatch and then disconnect the two D-Sub

connectors that connect the ships wiring to the antenna and then remove the

hatch.  



 



Right now I the two connectors do not have a back shell and when I mate the

two connectors I secure them togher with a tie wrap on each side through the

holes that the thumbscrew should go through.simple, lightweight, low tech,

and secure however not very professional.

argoldman(at)aol.com
Guest

Posted: Wed Apr 17, 2019 2:30 pm Post subject: Water resistant D-Sub

Bill, there are little female connectors (basically nuts) that you can screw both the affixing screws into joining the two shells together. Suggested to use thread locker with these. I think B&C carries them.

 



 S8013-hex

 



 Rich

 



 

 In a message dated 4/17/2019 2:59:22 PM Central Standard Time, billhuntersemail(at)gmail.com writes: 



   	  Quote: 	
		      

THANKS Bob!!! 

  

I bought these DB15 type connectors and I understand the concept of installing the back shell with the male thumbscrews to connect to an accessory such as my Lightspeed III ignition module.  

  

What I am not clear on is how to connect the male D-Sub to a female D-Sub inline with each having a back shell and one with a male thumb screw and the second with a female threaded nut.  

  

Example:  I have a Dynon GPS antenna mounted to a removeable hatch and I want to be able to unbolt the hatch and then disconnect the two D-Sub connectors that connect the ships wiring to the antenna and then remove the hatch.  

   

Right now I the two connectors do not have a back shell and when I mate the two connectors I secure them togher with a tie wrap on each side through the holes that the thumbscrew should go through&hellip;simple, lightweight, low tech, and secure however not very professional&hellip; 

  

  

&hellip; 

Thanks, 

Bill Hunter 

 

     

From: owner-aeroelectric-list-server(at)matronics.com (owner-aeroelectric-list-server(at)matronics.com) <owner-aeroelectric-list-server(at)matronics.com> On Behalf Of Robert L. Nuckolls, IIISent: Wednesday, April 17, 2019 9:05 AMTo: aeroelectric-list(at)matronics.com (aeroelectric-list(at)matronics.com)Subject: Re: Water resistant D-Sub 

 

 

  

At 06:03 PM 4/16/2019, you wrote:  	  Quote: 	
		   

Try this link for NorComp Seal-D D-sub connectors that meet IP66 or IP67.  You always have to specify a standard, because otherwise you don't know what you'll get.Newark, Mouser, Digi-Key and other distributors carry them.Waterproof D-Sub | IP67/IP68 Rated | NorComp Waterproof D-Sub | IP67/IP68 Rated | NorComp 

Search a full range of waterproof d-sub connectors used in a variety of harsh environments & demanding end-use a...Henador Titzoff 	
 

  Cool  find! Thank you. 

  Bob . . .

nuckolls.bob(at)aeroelect
Guest

Posted: Wed Apr 17, 2019 3:24 pm Post subject: Water resistant D-Sub

At 05:29 PM 4/17/2019, you wrote:

  	  Quote: 	
		  Bill, there are little female connectors (basically nuts) that you can screw both the affixing screws into joining the two shells together. Suggested to use thread locker with these. I think B&C carries them.



 S8013-hex 	


   Yeah. Looks like these



 [img]cid:7.1.0.9.0.20190417182319.054d98d8(at)aeroelectric.com.0[/img] 



  Got a boat load. Send me an address and

  quantity needed. I'll drop them in the mail.



 

 

   Bob . . .

15f5306.jpg

Description:

Filesize:

167.55 KB

Viewed:

6201 Time(s)

ceengland7(at)gmail.com
Guest

Posted: Wed Apr 17, 2019 6:13 pm Post subject: Water resistant D-Sub

On 4/17/2019 6:24 PM, Robert L.       Nuckolls, III wrote:

     

      	  Quote: 	
		         At 05:29 PM 4/17/2019, you wrote:

               	  Quote: 	
		  Bill,           there are little female           connectors (basically nuts) that you can screw both the           affixing screws           into joining the two shells together. Suggested to use thread           locker with           these. I think B&C carries them.

           

           S8013-hex 	
       

         Yeah. Looks like these

       

               

       

        Got a boat load. Send me an address and

        quantity needed. I'll drop them in the mail.

       

       

                

             Bob . . .                	
     I really like Dsubs, but I really hate the standard attachment     method (tiny, sloppily slotted screws). For some chassis mounts, and     most in-line pairs, I really like 'bale' style latches. Here's one     source:

 https://www.google.com/url?sa=i&source=images&cd=&cad=rja&uact=8&ved=2ahUKEwjYlKi7xNjhAhXLTN8KHfiPCrsQjRx6BAgBEAU&url=https%3A%2F%2Fwww.newark.com%2Fcooper-interconnect%2F17-529%2Fd-sub-spring-latch%2Fdp%2F39F1390&psig=AOvVaw064bp5kfjSPGEFC3WoLuOE&ust=1555638852183307

     

     May require modifying the backshell slightly.

     

     Charlie

     	          		Virus-free. www.avast.com 		 	 [url=#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2] [/url]

argoldman(at)aol.com
Guest

Posted: Wed Apr 17, 2019 6:15 pm Post subject: Water resistant D-Sub

Beg to differ, Bob. 



The devices to which I referred were totally of the female gender persuasion. The ones that you showed are male on one side and female on the other. 

Not so my suggestion. Both sides are female with opposite threads and are sized to hold two sub ds  together. See b& c catalog with the stock number that I indicated (unless I was dyslexic when I copied the number. )



Rich



Sent from my iPhone



On Apr 17, 2019, at 6:24 PM, Robert L. Nuckolls, III <nuckolls.bob(at)aeroelectric.com (nuckolls.bob(at)aeroelectric.com)> wrote:

 	  Quote: 	
		    At 05:29 PM 4/17/2019, you wrote:

  	  Quote: 	
		  Bill, there are little female connectors (basically nuts) that you can screw both the affixing screws into joining the two shells together. Suggested to use thread locker with these. I think B&C carries them.



 S8013-hex 	


   Yeah. Looks like these



 <15f5306.jpg> 



  Got a boat load. Send me an address and

  quantity needed. I'll drop them in the mail.



 

 

   Bob . . .

echristley(at)att.net
Guest

Posted: Wed Apr 17, 2019 6:29 pm Post subject: Water resistant D-Sub

That's what I'm using on my firewall to engine sensor bundle connector.  Keep in mind that these won't fit on all shells.  I actually have a bag full of shells now.  



                  

                                                                    On Wednesday, April 17, 2019, 7:14:24 PM MST, Charlie England <ceengland7(at)gmail.com> wrote:                 

                 



                 



                      On 4/17/2019 6:24 PM, Robert L.       Nuckolls, III wrote:     

      	  Quote: 	
		         At 05:29 PM 4/17/2019, you wrote:               	  Quote: 	
		  Bill,           there are little female           connectors (basically nuts) that you can screw both the           affixing screws           into joining the two shells together. Suggested to use thread           locker with           these. I think B&C carries them.                      S8013-hex 	
                Yeah. Looks like these                                     Got a boat load. Send me an address and        quantity needed. I'll drop them in the mail.                              

             Bob . . .                	


      I really like Dsubs, but I really hate the standard attachment     method (tiny, sloppily slotted screws). For some chassis mounts, and     most in-line pairs, I really like 'bale' style latches. Here's one     source: https://www.google.com/url?sa=i&source=images&cd=&cad=rja&uact=8&ved=2ahUKEwjYlKi7xNjhAhXLTN8KHfiPCrsQjRx6BAgBEAU&url=https%3A%2F%2Fwww.newark.com%2Fcooper-interconnect%2F17-529%2Fd-sub-spring-latch%2Fdp%2F39F1390&psig=AOvVaw064bp5kfjSPGEFC3WoLuOE&ust=1555638852183307          May require modifying the backshell slightly.          Charlie    Virus-free. www.avast.com 		[url=#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2] [/url]

billhuntersemail(at)gmail
Guest

Posted: Thu Apr 18, 2019 7:13 am Post subject: Water resistant D-Sub

Thanks Bob for your kind offer! I already ordered some from Amazon Aircraft

Supply but I greatly appreciate the offer and all of the advice



Thanks,



Bill Hunter



On Wed, Apr 17, 2019, 19:18 Charlie England <ceengland7(at)gmail.com> wrote:



[quote] On 4/17/2019 6:24 PM, Robert L. Nuckolls, III wrote:



 At 05:29 PM 4/17/2019, you wrote:



 Bill, there are little female connectors (basically nuts) that you can

 screw both the affixing screws into joining the two shells together.

 Suggested to use thread locker with these. I think B&C carries them.



 S8013-hex

   Yeah. Looks like these



  Got a boat load. Send me an address and

  quantity needed. I'll drop them in the mail.

   Bob . . .



 I really like Dsubs, but I really hate the standard attachment method

 (tiny, sloppily slotted screws). For some chassis mounts, and most in-line

 pairs, I really like 'bale' style latches. Here's one source:



 https://www.google.com/url?sa=i&source=images&cd=&cad=rja&uact=8&ved=2ahUKEwjYlKi7xNjhAhXLTN8KHfiPCrsQjRx6BAgBEAU&url=https%3A%2F%2Fwww.newark.com%2Fcooper-interconnect%2F17-529%2Fd-sub-spring-latch%2Fdp%2F39F1390&psig=AOvVaw064bp5kfjSPGEFC3WoLuOE&ust=1555638852183307



 May require modifying the backshell slightly.



 Charlie

 <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient&utm_term=icon> Virus-free

Display posts from previous:

	Matronics Email Lists Forum Index -> AeroElectric-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum