Matronics Email Lists :: View topic - Does Anyone Recognize This Starter Solenoid???

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Does Anyone Recognize This Starter Solenoid???

Matronics Email Lists Forum Index -> AeroElectric-List

View previous topic :: View next topic

Author Message

billhuntersemail(at)gmail
Guest

Posted: Wed Oct 09, 2019 4:35 pm Post subject: Does Anyone Recognize This Starter Solenoid???

Can someone PLEASE help me identify this starter solenoid and then I can get a schematic of it?

 

There is not marking numbers on it that I can see without removing it from the engine compartment (kind of a tight fit)..

 

I think it is a Wells 490F however I cannot determine it for sure.

 

I just had the engine out and all of the engine compartment wiring.  It worked before just fine.

 

It is installed it so that the left large post is connected to the master switched power bus source and the right post is connected to the starter motor.  

 

With that being said, I connected the starter switch wire to the left small post (the small post closest to the large powered post) and the starter indicator light to the right small post (closest to the starter motor post) and it did not start…

 

I then reversed the small wires so that the starter switch wire now goes to the right small post (the one closest to the starter motor post) and the indicator light is now connected to the left small post (the one closest to the powered bus) and the starter and indicator light work as expected.  So I would normally be happy however it seems to be backwards from what I expected…plus I do not know what direction to run my diode.

 

The questions now are:

 

-Is this the proper way to wire up this solenoid (I would have expected the starter switch wire should be connected to the post that is closest to the power supply and the indicator wire would be closest to the post that goes to the starter motor)?

 

-What direction do I connect the diode (from the ground to the right small post with the silver band pointed toward the right small post)?

 

Any help would be appreciated!!!

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

Solenoid.jpg

Description:

Filesize:

173.27 KB

Viewed:

3450 Time(s)

ceengland7(at)gmail.com
Guest

Posted: Wed Oct 09, 2019 5:24 pm Post subject: Does Anyone Recognize This Starter Solenoid???

On 10/9/2019 7:32 PM,       billhuntersemail(at)gmail.com (billhuntersemail(at)gmail.com) wrote:

     

      	  Quote: 	
		                         <![endif]-->   <![endif]-->                

Can someone PLEASE help me identify this           starter solenoid and then I can get a schematic of it?         

          

There is not marking numbers on it that I           can see without removing it from the engine compartment (kind           of a tight fit)..         

          

I think it is a Wells 490F however I cannot           determine it for sure.         

          

I just had the engine out and all of the           engine compartment wiring.  It worked before just fine.         

          

It is installed it so that the left large           post is connected to the master switched power bus source and           the right post is connected to the starter motor.           

          

With that being said, I connected the           starter switch wire to the left small post (the small post           closest to the large powered post) and the starter indicator           light to the right small post (closest to the starter motor           post) and it did not start…         

          

I then reversed the small wires so that the           starter switch wire now goes to the right small post (the one           closest to the starter motor post) and the indicator light is           now connected to the left small post (the one closest to the           powered bus) and the starter and indicator light work as           expected.  So I would normally be happy however it seems to be           backwards from what I expected…plus I do not know what           direction to run my diode.         

          

The questions now are:         

          

-Is this the proper way to wire up this           solenoid (I would have expected the starter switch wire should           be connected to the post that is closest to the power supply           and the indicator wire would be closest to the post that goes           to the starter motor)?         

          

-What direction do I connect the diode           (from the ground to the right small post with the silver band           pointed toward the right small post)?         

          

Any help would be appreciated!!!       

     	
     Easiest way to check for proper control terminal is to use an ohm     meter. Black to frame, red to each small terminal in turn. The     terminal for the light should show open circuit; the terminal for     the switched B+ (control) should read some relatively low     resistance, near zero ohms.

     

     Here's a link to one of Bob's instructional pdfs, but unfortunately,     it doesn't show the switched (light) terminal. That terminal gets     tied to the two 'fat' terminals when the contactor is activated; it     should be 'floating' (open circuit to all other terminals) when the     contactor is deactivated.

     http://www.aeroelectric.com/articles/strtctr.pdf

     

     Charlie

     

     

     	          		Virus-free. www.avast.com 		 	 [url=#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2] [/url]

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

user9253

Joined: 28 Mar 2008
Posts: 1922
Location: Riley TWP Michigan

Posted: Wed Oct 09, 2019 5:30 pm Post subject: Re: Does Anyone Recognize This Starter Solenoid???

The banded end of arc suppression diodes always connects to positive.

For this contactor, connect the banded end to the small terminal that gets positive voltage from the start switch.  Connect the other end of the diode to ground.

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

_________________
Joe Gores

billhuntersemail(at)gmail
Guest

Posted: Thu Oct 10, 2019 7:13 am Post subject: Does Anyone Recognize This Starter Solenoid???

THANK YOU very much Joe, Charlie, and Bob.  Greatly appreciate the info!!!



Bill



--

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

billhuntersemail(at)gmail
Guest

Posted: Thu Oct 10, 2019 7:52 am Post subject: Does Anyone Recognize This Starter Solenoid???

Found them!!!



As in the picture Bob sent...the S and I letters are on the downward facing

boss under the terminals.  I could not see them from above and I had to

remove some components and sneak up on them from underneath to be able to

read them...I could not even get my head wedged in there so I could see them

with my glasses on so I had to wedge my phone in there to make a picture (I

use this same picture taking technique to read menus at restaurants

nowadays).



Bob, it looks like that is the same solenoid that I have.  Do you have a

manufacturer and part number for that unit?



The next important question I have is...on my installation the big post on

the left is the powered bus and the big post on the right is the post that

gets wired to the starter motor...Since the S post is on the right side that

would lead me to believe that the big post on the right should be the

powered bus...does it really matter what big post goes to what???



--

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

Solenoid.jpg

Description:

Filesize:

104.79 KB

Viewed:

3430 Time(s)

user9253

Joined: 28 Mar 2008
Posts: 1922
Location: Riley TWP Michigan

Posted: Thu Oct 10, 2019 12:24 pm Post subject: Re: Does Anyone Recognize This Starter Solenoid???

 	  Quote: 	
		  .does it really matter what big post goes to what? 	
The starter will work either way.  However, the indicator light could remain on if wired backwards, depending on the internal connections.

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

_________________
Joe Gores

Display posts from previous:

	Matronics Email Lists Forum Index -> AeroElectric-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum