Matronics Email Lists :: View topic - Grounding shielded wire 1/4 from one side?

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

Grounding shielded wire 1/4 from one side?

Matronics Email Lists Forum Index -> AeroElectric-List

View previous topic :: View next topic

Author Message

nuckolls.bob(at)aeroelect
Guest

Posted: Fri Oct 23, 2020 2:30 pm Post subject: Grounding shielded wire 1/4 from one side?

At 01:18 PM 10/22/2020, you wrote:

  	  Quote: 	
		  --> AeroElectric-List message posted by: "rparigoris" <rparigor(at)hotmail.com>



 Hi Group I have a question about running a shielded wire to ground. On my Rotax 914 it has 2 shielded wires going from the Ducati ignition modules to the ignition ACS switch. The shield is connected to the ignition switch and is used to ground the Ducati ignition modules. Where the shielded wires go into the ignition connectors things get pretty tight and need to make sharp bends for several inches. The 2 shielded wires run right by my FWF ground field of tabs about 1/4 the total length from the ignition modules. Is there anything wrong with carefully removing the insulation on the shielded wires, wrapping ground wire to shield and carefully soldering then connect to field of tabs?:

 [url=https://1drv.ms/u/s!Ah1S270Nwg9V3VSqwoGL7YgsYS7Z?e=EsKSit] https://1drv.ms/u/s!Ah1S270Nwg9V3VSqwoGL7YgsYS7Z?e=EsKSit[/url]

 	


    What you proposed is probably fine . . .



    Ground shields to airframe in only one

    place (forest of tabs) using your

    proposed 'tap'. Use shields to SUPPLY

    ground at ignition switch.



    See attached . . . 



    Of course the assumed condition is that

    there exists a FAT wire jumper from engine

    crankcase to FWL stud.



 



 

 

   Bob . . .

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

Rotax_914_Ign_Wiring_Alternative.jpg

Description:

Filesize:

19.23 KB

Viewed:

1640 Time(s)

rparigoris

Joined: 24 Nov 2009
Posts: 792

Posted: Fri Oct 23, 2020 3:35 pm Post subject: Re: Grounding shielded wire 1/4 from one side?

Hi Bob



Thank you for reply. I have a #4 fat wire running from field of tab main negative 3/8" Brass bolt pass-through FW to the starter nub on my Rotax 914. Ron P.

- The Matronics AeroElectric-List Email Forum -

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?AeroElectric-List

Display posts from previous:

	Matronics Email Lists Forum Index -> AeroElectric-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum